To Next Page

To Previous Page

5-156 L30 Line Current Differential System GE Multilin

5.5 FLEXLOGIC 5 SETTINGS

Figure 5–59: FLEXELEMENT DIRECTION, PICKUP, AND HYSTERESIS

In conjunction with the

FLEXELEMENT 1 INPUT MODE setting the element could be programmed to provide two extra charac-

teristics as shown in the figure below.

FlexElement 1 OpSig

FLEXELEMENT 1 PKP

FLEXELEMENT

DIRECTION = Over

PICKUP

HYSTERESIS = % of PICKUP

FlexElement 1 OpSig

FLEXELEMENT 1 PKP

FLEXELEMENT

DIRECTION = Under

PICKUP

HYSTERESIS = % of PICKUP

842705A1.CDR

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware26
- Using the Relay27
2 Product Description31
- Introduction31
- Order Codes39
- Signal Processing49
  - Ur Signal Processing49
- Pilot Channel Relaying51
- Specifications54
3 Hardware67
- Description67
  - Panel Cutout67
  - Rear Terminal Layout73
- Wiring75
- Pilot Channel Communications97
4 Human Interfaces113
- Enervista Ur Setup Software Interface113
- Extended Enervista Ur Setup Features116
- Faceplate Interface125
5 Settings138
- Overview141
- Product Setup148
- System Setup230
- Flexlogic278
- Grouped Elements300
- Control Elements347
- Inputs and Outputs384
- Transducer Inputs and Outputs398
- Testing404
6 Actual Values409
- Overview409
  - Actual Values Menu409
- Status409
- Records431
- Product Information434
  - Model Information434
  - Firmware Revisions434
7 Commands and435
- Commands435
8 Theory of Operation449
- Overview449
- Operating Condition Characteristics464
- Fault Locator470
9 Application of Settings471
- Ct Requirements471
  - Introduction471
  - Ct Saturation Analysis Tool472
- Current Differential (87L) Settings474
- Channel Asymmetry Compensation Using Gps477
- Instantaneous Elements480
  - Instantaneous Element Error During L30 Synchronization480
10 Commissioning485
- Testing485
11 Maintenance489
- Modules489
  - Replace a Module489
- Batteries491
  - Replace Battery491
  - Dispose of Battery493
- Uninstall and Clear Files and Data496
- Repairs497
- Storage498
- Disposal499
Parameter Lists501
- Flexanalog Items501
- A.1.1 Flexanalog Items501
- Flexinteger Items509
- A.1.2 Flexinteger Items509
Modbus Communications511
Modbus Rtu Protocol511
- Introduction511
- Physical Layer511
- Data Link Layer511
- B.1.1 Introduction511
- Modbus Rtu Crc-16 Algorithm512
Modbus Function Codes514
- Supported Function Codes514
- Read Actual Values or Settings (Function Code 03/04H514
- Execute Operation (Function Code 05H515
- Store Single Setting (Function Code 06H515
- Store Multiple Settings (Function Code 10H516
- Exception Responses516
File Transfers517
- Obtaining Relay Files Via Modbus517
Memory Mapping519
- Modbus Memory Map519
- Data Formats582
- B.4.2 Data Formats582
Iec 61850619
Overview619
- Introduction619
- Communication Profiles619
- C.1.1 Introduction619
- File Transfer by Iec 61850620
Server Data Organization621
- Overview621
- Ggio1: Digital Status Values621
- Ggio2: Digital Control Values621
- Ggio3: Digital Status and Analog Values from Goose Data621
- Ggio4: Generic Analog Measured Values621
- C.2.1 Overview621
- Mmxu: Analog Measured Values622
- Protection and Other Logical Nodes622
Server Features and Configuration624
- Buffered/Unbuffered Reporting624
- File Transfer624
- Timestamps and Scanning624
- Logical Device Name624
- Location624
- Logical Node Name Prefixes625
- Connection Timing625
- Non-Iec 61850 Data625
- Communication Software Utilities625
Generic Substation Event Services: Gsse and Goose626
- Overview626
- Gsse Configuration626
- Fixed Goose626
- Configurable Goose626
- C.4.1 Overview626
- Ethernet Mac Address for Gsse/Goose629
- Gsse ID and Goose ID Settings629
Iec 61850 Implementation Via Enervista Ur Setup630
- Overview630
- C.5.1 Overview630
- Configuring Iec 61850 Settings631
- About ICD Files632
- Creating an ICD File with Enervista Ur Setup636
- About Scd Files636
- Importing an Scd File with Enervista Ur Setup639
Acsi Conformance641
- Acsi Basic Conformance Statement641
- Acsi Models Conformance Statement641
- Acsi Services Conformance Statement642
Logical Nodes645
Iec 60870-5-103649
- Overview649
- Factor and Offset Calculation to Transmit Measurand649
- D.1.1 Overview649
- Interoperability Document650
- D.1.3 Interoperability Document650
- Interoperability Document655
- E.1.1 Interoperability Document655
- Point List663
- E.1.2 Point List663
Device Profile Document665
- Dnp V3.00 Device Profile665
- F.1.2 Implementation Table668
Dnp Point Lists672
- Binary Input Points672
- Binary and Control Relay Output673
- Counters674
- F.2.3 Counters674
- Analog Inputs675
- F.2.4 Analog Inputs675
Radius Server Configuration677
Change Notes679
- Revision History679
- Changes to the L30 Manual679
- H.1.1 Revision History679
Abbreviations684
- Standard Abbreviations684
  - H.2.1 Standard Abbreviations684
  - H.3.1 Ge Multilin Warranty687
Warranty688

Questions and Answers:

Need help?

Do you have a question about the GE L30 and is the answer not in the manual?

GE L30 Specifications

General

Brand	GE
Model	L30
Category	Relays
Language	English

Related product manuals

GE L30 User Manual

Table of Contents

Questions and Answers:

GE L30 Specifications

Related product manuals