ESSENTIAL PROGRAMMING
All Programming must be done when the Communicator is in the “OFF” position (1234 ESC).
HOW TO RECORD THE VOICE MESSAGES:
Quick guide: Press 1 2 3 4 > RECORD > 1 > ENTER, Record message now
(Note: 1 = message for Trigger 1; 2 = message for Trigger 2, etc; 0 = Test Message, if required.)
1. Key in the four digit user PASSWORD code (factory default 1234).
2. Press RECORD.
3. Press 1 (to record as the message for Trigger 1) or 2 (to record as the message for Trigger 2, etc) or 0
(to record the Test Message). If a Test Message is required, it then needs to be programmed as active
as a daily, weekly or monthly test call.
4. Press ENTER to start recording the message. You now have 10 seconds to record your message.
5. Press ENTER to stop the recording, or wait for the 10 seconds to end.
HOW TO PLAY BACK THE VOICE MESSAGES:
Quick guide: Press 1 2 3 4 > PLAY > 1 > ENTER to play back the recorded messages
(Note: 1 = the first message; 2 = the second message; 0 = Test Message.)
HOW TO CHANGE THE USER PASSWORD (Factory Default 1234):
Quick guide: Press 1 2 3 4 > PASSWORD > New Code > ENTER
1. Key in the four digit user <PASSWORD> code. Factory Default 1234.
2. Press PASSWORD.
3. The LCD will display “PASSWORD”.
4. Key in your new four digit code and press ENTER.
5. You have now changed to your new four digit password.
HOW TO PROGRAM PHONE NUMBERS:
You can enter a maximum of 9 Telephone Numbers for the Triggers – each number can be a maximum of 32 digits.
Quick guide: Press 1 2 3 4 > PROGRAM > 3 > ENTER > 1 > ENTER > Telephone Number > ENTER
1. Key in the four digit user PASSWORD code (Factory Default 1234).
2. Press PROGRAM > 3 > ENTER > “X”. The number “X” you press after the ENTER button will select the
position in the sequence you want that telephone number to dial (1 = 1
st
number called; 2 = 2
nd
number called).
3. Key in the 1
st
telephone number.
4. Press ENTER to exit the programming mode.
5. Repeat the process until you have entered all the numbers you wish the Communicator to call once it
has been triggered (maximum 9 different numbers). You can repeat the same number(s) if you wish.
HOW TO DELETE PHONE NUMBERS:
Quick guide: Press 1 2 3 4 > PROGRAM > 3 > ENTER > 1 > ENTER > DELETE > ENTER
1. Key in the four digit user Password code (Factory Default 1234).
2. Press PROGRAM > 3 > ENTER. Select the position for the telephone number you want to delete (1 =
1
st
number called; 2 = 2
nd
number called), Press DELETE. The LCD display will show “DELETE”. Press
ENTER to delete or ESC to keep the number and exit programming.
HOW TO DESIGNATE TELEPHONE NUMBERS TO TRIGs 1, 2, 3, 4, 5 and 6 + THE TEST CALL:
(Factory Default – All numbers are called for each Trigger input and the Test Call.) Only these Telephone Numbers will be
called/SMS sent to on activation of the respective Trigger input.
Quick guide: Press 1 2 3 4 > PROGRAM > 6 > ENTER > X > ENTER > N > ENTER
1. Key in the four digit user Password code (Factory Default 1234).
2. Press PROGRAM > 6 > ENTER
3. Press 1 (for TRIG 1), or Press 2 (for TRIG 2), etc. Press 0 for the Test Call. Press ENTER
Page 4
To Next Page
Loading...