Glacier bay N2428E User Manual (English)

Questions and Answers:

J
Jacob HendricksAug 4, 2025
What to do if Glacier Bay Toilets water continues to run?
- M
  Michael HartAug 4, 2025
  If water continues to run in your Glacier Bay toilet, first, check that the flapper is completely closed and clear any debris from the flapper and the sealing area of the flush valve. Debris may obstruct the full closure. Also, make sure the flapper chain isn't too tight. Adjust the chain length to ensure the flapper can completely close, leaving only a small amount of play between the flush lever and the chain.
M
Matthew RuizAug 9, 2025
How to fix a Glacier bay N2428E Toilets fill valve that won't turn on or off?
- M
  Matthew WilsonAug 9, 2025
  To fix a Glacier Bay toilet fill valve that won't turn on, won't turn off, or won't refill the tank after the flush, remove the top cap and check for any debris. If you find debris or the water flow is weak, inspect the lower section of the fill valve for a partial blockage, which may be at the shut-off valve or in the water supply line. If the fill valve has been in use for a while and/or the float cup doesn't drop when flushing the tank, replace the seal with a genuine Fluidmaster 242 seal.
L
Lori JonesAug 14, 2025
What to do if my Glacier bay N2428E Toilets is constantly running?
- M
  Marco WilsonAug 14, 2025
  If water continues to run in your Glacier Bay toilet, first, check that the flapper is completely closed and clear any debris from it and the sealing area of the flush valve. Debris might prevent full closure. Also, make sure the flapper chain isn't too tight. Adjust the chain length, leaving a small amount of play between the flush lever and the chain, to ensure the flapper closes properly.
A
Andrea HernandezAug 19, 2025
Why Glacier Bay Toilets fill valve won't turn on or off?
- J
  Joshua DeanAug 19, 2025
  If the fill valve on your Glacier Bay toilet won't turn on, off, or refill the tank after flushing, start by removing the top cap and checking for debris. If you find debris or the flow is weak, inspect the lower section of the fill valve for partial blockage. The blockage may be at the shut-off valve or in the water supply line. If the fill valve has been in use for a while or the float cup doesn't drop when flushing the tank, replace the seal with a genuine Fluidmaster 242 seal.
S
Selena PollardAug 25, 2025
Why is the flush quality of my Glacier bay N2428E poor?
- M
  Michael MccoyAug 25, 2025
  If the flush quality of your Glacier Bay toilet is poor, ensure the water level in the tank reaches the water line printed on the overflow tube of the flush valve. You can raise the float cup by turning the adjustment screw on the fill valve clockwise to increase the water level. Also, check that the flapper chain isn't too loose. Adjust the chain length to ensure the flapper closes completely, with only a small amount of play between the flush lever and the chain.
C
Christian VelazquezAug 29, 2025
How to improve the flush quality of Glacier bay N2428E?
- W
  William MorrisAug 29, 2025
  If your Glacier Bay toilet's flush quality is poor, ensure the water level in the tank reaches the water line printed on the overflow tube of the flush valve. To raise the water level, turn the adjustment screw on the fill valve clockwise to raise the float cup. Also, check that the flapper chain isn't too loose. Adjust the chain length to ensure the flapper can completely close, leaving only a small amount of play between the flush lever and the chain.

Glacier bay N2428E Specifications

General

Type	Two-Piece
Bowl Shape	Elongated
Water Consumption	1.28 GPF
Material	Vitreous China
Color	White
Rough-In Size	12 inches
Seat Height	16.5 inches
Trapway Size	2 inches
Bowl Height	16.5 inches