rev. 5/30/2012
July 2012 U.S.A Parts Price List
Item No. Item Description List $
L3030100 DRIVE BELT $124.00
L3030709 STONE, HONING $15.20
L3030710 STONE, SHARPENING $15.20
L3040313 CAPACITOR 10UF $35.20
L4010064 INSERT, KNIFE COVER $10.40
L4020172 COVER, KNIFE $368.00
L4020305 KNOB, CHUTE SUPPORT $34.00
L4090304 STUD, KNOB, KNIFE GUARD $26.40
L4090325 HANDLE, ENDWEIGHT $44.00
L4100682 SHAFT, KNIFE GUARD $46.00
L4100715 PIN, NYLON, REAR-LOCATING $20.40
M002 KNOB, TABLE ADJUSTING $17.80
M003 WAVE WASHER C12, G10, G12, G12A $1.00
M004 TABLE ADJUSTING CAM C12, G10, G12, G12A $17.40
M005 TABLE SLIDE G10, G12, G12A $58.00
M013 STUD, CAM ACTUATOR C12, G10, G12, G12A $1.80
M014 ROD, TABLE SLIDE G10, G12, G12A $13.60
M015 SCREW $0.80
M016 PLATE,TABLE SLIDE C12, G10, G12, G12A $3.80
M017 SCREW G12A $0.80
M018 SHAFT, KNIFE PULLEY G12, G12A $50.40
M020 BEARING C12, G10, G12, G12A $15.40
M021 BUSHING (SPACER) G12, G12A $8.60
M024 DRIVE BELT G12, G12A $23.00
M025 KNIFE HUB COLLAR $13.80
M026 MICROSWITCH G10, G12, G12A $17.80
M030 1/3 HP MOTOR G12, G12A $221.00
M031 MOTOR PIN C9, C10, C12, G10, G12, G12A $3.40
M032 SCREW $0.80
M033 STUD $0.80
M034 NUT $0.80
M035 FLAT WASHER $0.80
M036 ON/OFF SWITCH $11.20
M038 RESET SWITCH C9, C10, C12, G10, G12, G12A $17.40
M039 CAPACITOR 16 UF C9, C10, C12, G10, G12, G12A $30.80
M043 STUD G10 $6.40
M044 KNIFE RING GUARD G12, G12A $142.00
M045 STUD,KNIFE RING GUARD G10, G12, G12A $4.80
M046 SCREW $0.80
M047 KNIFE C12, G12, G12A $262.00
M048 SCREW $0.80
M049A KNIFE COVER INSERT GC12B $9.40
M051 CHEFMATE KNIFE COVER KNOB $1.00
M053 STUD C9, C10, C12, G10, G12, G12A $1.20
M056 BEARING $8.00
M057 BUSHING,CHUTE SLIDE ASSEMBLY C12, G10, G12, G12A
$2.80
M059 SLIDE ROD,ROUND C12, G10, G12, G12A $26.20
M060 SCREW,SLIDE ROD C12, G10, G12, G12A $3.40
M061 SPRING,SLIDE ROD,ROUND C12, G10, G12, G12A $1.00
M062 SLIDE BAR, SQUARE C12, G10, G12, G12A $17.00
M063 WEAR STRIP,SLIDE BAR,SQUARE C12, G10, G12, G12A $9.20
M064 SCREW $0.80
M066 CHUTE SUPPORT G10, G12, G12A $99.60
To Next Page
Loading...
