What causes a broken dough hook on a Globe SP10?
A dough hook can break if: * The batch size is too large for the mixer. Reduce batch size and adjust the recipe. * The ingredients are too cold or too large. Wait for ingredients to reach room temperature before mixing and reduce chunk size.
What to do if my Globe SP10 Mixer won't turn on?
If your Globe Mixer won't turn on, check that the bowl guard is fully closed by rotating it to the right. Ensure the bowl is raised to its highest position. Verify the timer is engaged by turning it past '0' or setting it to the green 'on' position. Confirm all power connections and the circuit breaker are working. Also, make sure the gear is fully engaged.
What to do if my Globe Mixer stops during the mixing cycle?
If your Globe Mixer stops during the mixing cycle, it could be due to a few reasons: * The internal overload might have tripped. For SP25 and smaller models, press the stop button, then the reset button on the back of the mixer. For larger models, wait two minutes, then press ‘Start’ to restart the mixer. Reduce batch size or adjust recipe if this continues to occur! * Speeds were changed during mixing, SP80PL only. Return speed control lever to a speed model position and restart the mixer.
How to reduce noise from a Globe SP10 Mixer?
If your Globe Mixer is making excessive noise, consider the following: * Ensure the mixer is installed on a level surface. Adjust the surface or relocate the mixer, and make sure the rubber feet are installed. * Check that the bowl is seated correctly and the clamps are in place. Ensure the bowl is seated into the bowl cradle correctly and bowl clamps are locked into place. * Verify the agitator is fitted properly. Remove and reattach the agitator into position properly. * Avoid overloading the bowl. Reduce batch size.
Why Globe Mixer will not mix medium or heavy loads?
Your Globe Mixer might struggle with medium or heavy loads if there is incorrect or low voltage.
Why my Globe SP10 won't turn on?
Your Globe Mixer might not be operating due to several reasons: * The bowl guard might not be in the closed position. Rotate the guard to the right until it is fully closed. * The bowl might not be raised to the highest position. Ensure the bowl is fully raised. * There might be a power issue. Check all power connections and plug the mixer into a live socket, without using an extension cord. Test the socket with another item to confirm it's working. * The building circuit breaker might be off. Check the breaker box. * The internal overload might have tripped. For SP25 and smaller models, press the stop button, then the reset button on the back of the mixer. For larger models, wait two minutes, then press ‘Start’ to restart the mixer. Reduce batch size or adjust recipe if this co...
Why does my Globe Mixer stop during mixing?
Your Globe Mixer might stop during mixing due to a few reasons. One possibility is that the internal overload has tripped. For SP25 and smaller models, press the stop button then the reset button. For larger models, wait two minutes, then press the stop button and then the start button. Note that repeated tripping might indicate the need to reduce batch size or adjust the recipe. Another cause could be damaged or broken transmission belt, which would require a technician to replace it for SP25 and larger models. Lastly, if you have an SP80PL model, changing speeds during mixing can cause it to stop; return the speed control lever to a speed model position and restart the mixer.
Why is my Globe Mixer not running?
Your Globe Mixer might not be running due to several reasons. Ensure the bowl guard is fully closed by rotating it to the right. Check that the bowl is raised to its highest position. Make sure the timer is engaged by turning it at least five minutes past '0', then set it to the desired time or the green 'on' position. Verify all power connections and plug the mixer into a live socket, avoiding extension cords, and test the socket. Also, check the building's circuit breaker. If the internal overload tripped, for SP25 and smaller models, press the stop button, then the reset button; for larger models, wait two minutes, press the stop button, then the start button. Finally, ensure the gear is fully engaged by switching it into position, as the mixer won't operate if the speed control lever i...
Why is there residue leaking from the hub of my Globe SP10?
Residue leaking from the hub is caused by a contaminated hub due to build-up of meat and/or vegetable juices (especially tomatoes). To avoid this problem, always wipe the hub and dry it after each use. Note that acid from tomato juices will corrode/contaminate interior parts, so avoid mixing tomatoes in a meat grinder!
Why are the whip wires broken on my Globe SP10?
Broken whip wires can occur if: * The batch size is too large for the mixer. Reduce the batch size and adjust the recipe. * The mixture is too firm, or the speed is too high. Reduce the speed. * A hand utensil was dropped into the bowl while mixing. Always stop the mixer before working on the mixture.
General environmental, safety, and occupational health notices for mixer operation.
Precautions for servicing live equipment and essential resuscitation info for personnel.
Guidelines on industrial hygiene requirements and handling of consumable materials.
Procedures for unpacking the mixer and initial setup steps.
Guidance on connecting the mixer to electrical power, including grounding.
Specific instructions for operating three-phase mixer units, including rotation checks.
Safety precautions, bowl guard, and bowl handling procedures.
Attaching agitators, mixing ingredients, speed selection, and capacity charts.
Using attachment hub and digital controls for SP62P/SP80PL models.
Important precautions to follow before and during the cleaning process.
Detailed recommendations for cleaning mixer parts and their frequency.
Key points for installation, operation, and maintenance of the mixer.
A schedule outlining recommended maintenance tasks and their frequency.
Schematic diagram illustrating the electrical components and connections for the SP25 mixer.
Catalog of parts for Globe mixers, models SP25 & SPC25.
Price list for Globe Food Equipment Co. parts, dated July 2012.
General| Manufacturer | Globe |
|---|---|
| Model | SP10 |
| Type | Planetary Mixer |
| Speeds | 3 |
| Capacity | 10 qt |
To Next Page
