Globe SP10 - User Manual

101 pages

To Next Page

To Next Page

Loading...

S6161-1K-FSE-010

0910-LP-113-0781

INSTRUCTION MANUAL FOR

GLOBE MIXER MODEL SP-25

N00024-11-C-2111

GLOBE FOOD EQUIPMENT COMPANY

2153 DRYDEN RD.

DAYTON, OH 45439

DISTRIBUTION STATEMENT B: DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES

ONLY. PROPRIETARY INFORMATION: APRIL 2013. OTHER REQUESTS SHALL BE REFERRED TO

COMNAVSEASYSCOM 07L. NO SECONDARY DISTRIBUTION AUTHORIZED WITHOUT WRITTEN

APPROVAL OF THE APPLICABLE COMNAVSEASYSCOM PROGRAM MANAGEMENT OFFICE.

WARNING- THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY

THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC 2751, ET. SEQ.) OR THE EXPORT

ADMINISTRATION ACT OF 1979, AS AMENDED, TITLE 50, U.S.C. APP. 2401 ET. SEQ. VIOLATIONS OF

THESE EXPORT LAWS ARE SUBJECT TO SEVERE CRIMINAL PENALTIES. DISSEMINATE IN

ACCORDANCE WITH PROVISIONS OF OPNAVINST 5510.161.

DESTRUCTION NOTICE- DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF

CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

PUBLISHED BY DIRECTION OF COMMANDER, NAVAL SEA SYSTEMS COMMAND

APRIL 29, 2013

Other manuals for Globe SP10

Owner's Manual20 pages

Questions and Answers

D
David SmithAug 23, 2025
What to do if my Globe SP10 stops during mixing?
- A
  Amy BurnsAug 23, 2025
  If your Globe Mixer stops during mixing, it could be due to a few reasons. First, the internal overload might have tripped. For SP25 and smaller models, press the stop button, then the reset button. For larger models, wait two minutes, press the stop button, then the start button. If the overload continues to trip, consider reducing the batch size or adjusting the recipe. Another cause could be a damaged or broken transmission belt, in which case you should contact a technician to replace the belt, applicable for SP25 and larger models. Lastly, if you have an SP80PL model, ensure you're not changing speeds during mixing; return the speed control lever to a speed model position and restart the mixer.
D
diana39Sep 6, 2025
Why are the whip wires broken on my Globe SP10?
- J
  Joshua StaffordSep 6, 2025
  Broken whip wires can occur if: * The batch size is too large for the mixer. Reduce the batch size and adjust the recipe. * The mixture is too firm, or the speed is too high. Reduce the speed. * A hand utensil was dropped into the bowl while mixing. Always stop the mixer before working on the mixture.
J
John EvansSep 5, 2025
What to do if bowl raise sticking or not operational on Globe SP10?
- M
  Melissa MejiaSep 5, 2025
  If the bowl raise mechanism is sticking or not operational, it is likely due to a lack of lubrication on the bowl slides. Lubricate the bowl slides with mineral oil or food quality grease.
L
Lauren VaughnSep 4, 2025
How to attach agitators easily onto the planetary shaft of Globe SP10?
- J
  Johnny HillSep 4, 2025
  If the agitators are difficult to attach to the planetary shaft, it may be due to a lack of lubrication or cleaning of the shaft. Wipe the planetary shaft with a clean damp cloth and lubricate it with mineral oil or food quality grease.
N
Noah MortonSep 2, 2025
Why is the mixing time too long with my Globe SP10 Mixer?
- B
  Brianna WrightSep 2, 2025
  If the mixing time is too long, it might be because: * The three-phase mixer is wired wrong. The agitators should rotate clockwise around the bowl; if not, an electrician must rewire it. * The batch size is too small. Increase the batch size or use a smaller bowl adapter kit. * The recipe portions or temperatures are incorrect. Follow the recipe instructions for portions and temperatures.
C
Courtney StevensSep 1, 2025
What to do if agitators touching bottom or sides of bowl of Globe Mixer?
- J
  James ReeseSep 1, 2025
  If the agitators are touching the bottom or sides of the bowl, the bowl may be defective or dented. Remove any dents or replace the bowl. Alternatively, the agitator itself may be defective, in which case, replace the agitator.
J
Jean WernerAug 30, 2025
Why Globe Mixer will not mix medium or heavy loads?
- C
  Christine MyersAug 30, 2025
  Your Globe Mixer might struggle with medium or heavy loads if there is incorrect or low voltage.
S
Steven GlennAug 29, 2025
How to reduce noise from a Globe SP10 Mixer?
- H
  hannah84Aug 29, 2025
  If your Globe Mixer is making excessive noise, consider the following: * Ensure the mixer is installed on a level surface. Adjust the surface or relocate the mixer, and make sure the rubber feet are installed. * Check that the bowl is seated correctly and the clamps are in place. Ensure the bowl is seated into the bowl cradle correctly and bowl clamps are locked into place. * Verify the agitator is fitted properly. Remove and reattach the agitator into position properly. * Avoid overloading the bowl. Reduce batch size.
D
Duane NelsonAug 27, 2025
What to do if my Globe Mixer stops during the mixing cycle?
- M
  Martin MuellerAug 27, 2025
  If your Globe Mixer stops during the mixing cycle, it could be due to a few reasons: * The internal overload might have tripped. For SP25 and smaller models, press the stop button, then the reset button on the back of the mixer. For larger models, wait two minutes, then press ‘Start’ to restart the mixer. Reduce batch size or adjust recipe if this continues to occur! * Speeds were changed during mixing, SP80PL only. Return speed control lever to a speed model position and restart the mixer.
W
Warren HarperAug 25, 2025
What to do if my Globe SP10 Mixer won't turn on?
- D
  Deanna ClarkAug 25, 2025
  If your Globe Mixer won't turn on, check that the bowl guard is fully closed by rotating it to the right. Ensure the bowl is raised to its highest position. Verify the timer is engaged by turning it past '0' or setting it to the green 'on' position. Confirm all power connections and the circuit breaker are working. Also, make sure the gear is fully engaged.

Globe SP10 Specifications

General

Manufacturer	Globe
Model	SP10
Type	Planetary Mixer
Speeds	3
Capacity	10 qt

Summary

Safety Summary

General Safety Practices

General environmental, safety, and occupational health notices for mixer operation.

Servicing Live Equipment and Resuscitation

Precautions for servicing live equipment and essential resuscitation info for personnel.

Industrial Hygiene and Consumable Materials

Guidelines on industrial hygiene requirements and handling of consumable materials.

Attention Owners and Operators

Key Components of the Mixer

Installation

Unpacking and Setup

Procedures for unpacking the mixer and initial setup steps.

Electrical Connection

Guidance on connecting the mixer to electrical power, including grounding.

Three Phase Unit Operation

Specific instructions for operating three-phase mixer units, including rotation checks.

Operating Instructions

Safety and Basic Operations

Safety precautions, bowl guard, and bowl handling procedures.

Mixer Setup and Usage

Attaching agitators, mixing ingredients, speed selection, and capacity charts.

Advanced Features and Attachments

Using attachment hub and digital controls for SP62P/SP80PL models.

Cleaning Instructions

Cleaning Precautions

Important precautions to follow before and during the cleaning process.

Recommended Cleaning Procedures

Detailed recommendations for cleaning mixer parts and their frequency.

Important Points

Installation, Operation, and Maintenance Guidelines

Key points for installation, operation, and maintenance of the mixer.

Recommended Maintenance Schedule

A schedule outlining recommended maintenance tasks and their frequency.

Capacity Chart

Troubleshooting

Limited Mixer Warranty

Part 2 Electrical Diagram

SP25 Electrical Diagram

Schematic diagram illustrating the electrical components and connections for the SP25 mixer.

Part 3 Parts Catalog

Mixer Parts Listing

Catalog of parts for Globe mixers, models SP25 & SPC25.

Part 4 Parts Price List

Globe Food Equipment Co. Parts List

Price list for Globe Food Equipment Co. parts, dated July 2012.

Related product manuals

Preview: Globe SP05

Preview: Globe SP62P-4