Product specifications:
Ÿ Dimensions: approx. 15 x 25 cm x 9 cm
Ÿ Weight: approx. 2.0 kg
Ÿ Connection cable: 30 cm + plug (CEE red 16 A or CEE red 32 A)
Ÿ Rated voltage: 230/400 V depending on number of connected phases
Ÿ Rated frequency: 50 Hz
Permissible ambient conditions:
Ÿ Temperature: -25 °C to + 40 °C
Ÿ Average temperature in 24 hours: below 35 °C
Ÿ Altitude: maximum 2,000 m above sea level
Ÿ Relative humidity: maximum 95 % (non-condensing)
Charging capacity:
Ÿ Maximum charging power 11 kW (16 A 3-phase | HOME+ 11 kW) or 22 kW (32 A 3-phase | HOME+ 22 kW)
Ÿ Charging power adjustable between 1.4 kW and 11 kW (HOME+ 11 kW) or 22 kW (HOME+ 22 kW) (via the charging
current in 1 ampere steps between 6 A and 32 A) depending on number of phases (not adjustable at go-eCharger!)
◦ single-phase: 1.4 kW to 3.7 kW or 7.4 kW
◦ two-phase: 2.8 kW to 7.4 kW or 14.8 kW (ATTENTION: applies to vehicles with 2-phase on-board chargers.
2-phase connection of the charger is not possible - go-eCharger needs to be connected 1- or 3-phase!)
◦ three-phase: 4.2 kW to 11 kW or 22 kW (go-eCharger switches through the power of the connection.)
Optional adapters:
Vehicle side connection:
Ÿ (type 2 cable not included in go-eCharger delivery)Type 2 socket
Ÿ Locking device (theft protection)
Ÿ Vehicles with type 1 can be charged with adapter cable
Ÿ Ampere and charging status readable via LED ring or app
Ÿ Charging power adjustable via button and app
Security features:
Ÿ RFID access control
Ÿ with DC detection, 30 mA AC, 6 mA DCRCD protection device
Ÿ Phase and voltage test of the input voltage
Ÿ Phase test after contactor
Ÿ Current sensor 3-phase
Ÿ Ground check for TT, TN mains (switchable grounding monitoring - Norway mode - for IT mains)
Ÿ Customer replaceable fine fuse for internal electronics (triggers if supply line is connected incorrectly)
Ÿ Adapter detection with automatic reduction to 16 A (for go-eCharger HOME+ 22 kW and only when using original go-
e adapters)
Ÿ IP54 - Protection against dirt and water, suitable for permanent outdoor use
Ÿ Impact resistance = Ik10
Ÿ Protection class = I
Ÿ Pollution degree = II
Ÿ go-e network operator API for authorised access of the electricity network operator to the go-eCharger for network
related power control
App an connectivity:
Ÿ Local (WiFi hotspot) or worldwide (via WiFi) usable
Ÿ Charge monitoring (voltage, current, power, energy)
Ÿ Start/stop function
Ÿ RFID card management (up to 10 users per charger)
Ÿ Timer
Ÿ Electricity meter (total kWh and total amount per RFID card)
Ÿ Max Wh Charging
Ÿ Access management (RFID/App)
Ÿ Lock/Unlock functions
Ÿ Electricity price exchange connection with intelligent charge management
Ÿ Load balancing
Ÿ Photovoltaic connection via open API interface (programming required)
Ÿ LED adjustment
Ÿ Management of the charging levels via button on the charging box
Ÿ Modbus TCP (firmware version 0.40 or higher) for power control by the electricity network operator
Ÿ Updateable for later functions (Smart-Home,...)
16 A CEE (red)
16 A multiple domestic plugs
16 A CEE campingplug (blue)
Page 10 Page 11
Scope of delivery
16 A multiple domestic plugs
16 A CEE campingplug (blue)
32 A CEE (red)
Ÿ 22 kW HOME+ to CEE red 16 A (3-phase)
Ÿ 22 kW HOME+ to CEE blue 16 A (1-phase)
Ÿ 22 kW HOME+ to CEE blue 32 A (1-phase)
Ÿ 22 kW HOME+ to multiple domestic plugs 16 A
Technical specifications
Optional
go-eCharger adapter cable
22 kW charging box
with 32 A CEE plug
11 kW charging box
with 16 A CEE plug
or
for HOME+ 11 kW for HOME+ 22 kW
RFID chip
Reset card
Wall mounting plate Mounting set
22 kW type 2 cable
2.5 meters
5.0 meters
7.5 meters
4 x dowels/screws for mounting plate
1 x dowel/screw for u-piece
1 x u-piece for optional cable protection
Spare fine-wire fuse
Ÿ 11 kW HOME+ to CEE red 32 A (3-phase)
Ÿ 11 kW HOME+ to CEE blue 16 A (1-phase)
Ÿ 11 kW HOME+ to multiple domestic plugs
16 A (household socket outlet)
To Next Page
Loading...
