What to do if my Goodwe Inverter shows Utility Loss?
If your Goodwe Inverter shows a 'Utility Loss' error, it means the grid is not connected. First, check the grid connection cables and make sure they are properly connected. Then, verify the grid's usability to ensure it is functioning correctly.
How to fix Over Temperature error on Goodwe GW4600-SS Inverter?
If your Goodwe inverter is showing an 'Over Temperature' error, it means the internal temperature is higher than the normal specified value. To resolve this: * Reduce the ambient temperature around the inverter. * Move the inverter to a cooler location. If the issue persists, further assistance may be needed.
What to do if Goodwe GW4600-SS Inverter shows Ground I Failure?
If your Goodwe Inverter displays a 'Ground I Failure', it indicates that the ground current is too high. Unplug the inputs from the PV generator and check the peripheral AC system. When the problem is cleared, reconnect the PV panel and check the inverter status.
How to troubleshoot Isolation Failure on a Goodwe GW4600-SS?
To address an 'Isolation Failure' on your Goodwe Inverter, check the impedance between PV (+) & PV (-) and ensure the PV inverter is earthed. The impedance value must be greater than 2M?. If the problem persists, further assistance may be needed.
What causes PV Over Voltage on a Goodwe Inverter?
If your Goodwe Inverter is showing a 'PV Over Voltage' error, check whether the PV open voltage is higher or too close to the maximum input voltage. If the problem still exists when the PV voltage is less than the maximum input voltage, further assistance may be needed.
What to do if my Goodwe GW4600-SS has Vac Failure?
If your Goodwe Inverter shows a 'Vac Failure', the PV Inverter will automatically restart within 5 minutes if the grid returns to normal. Also, make sure grid voltage conforms with the specification. If the problem still exists, further assistance may be needed.
What does Fac Failure mean on a Goodwe GW4600-SS?
If your Goodwe Inverter displays a 'Fac Failure', the PV Inverter will automatically restart within 5 minutes if the grid returns to normal. Also, make sure grid frequency is in conformity with the specification. If the problem still exists, further assistance may be needed.
How to resolve Consistent Failure on a Goodwe GW4600-SS?
If your Goodwe Inverter is experiencing a 'Consistent Failure', disconnect PV (+) or PV (-) from the input and restart the PV Inverter. If the problem still exists, further assistance may be needed.
What to do for Relay-Check Failure on Goodwe Inverter?
To address a 'Relay-Check Failure' on your Goodwe Inverter: 1. Disconnect all PV (+) or PV (-). 2. Wait for a few seconds. 3. After the LCD switches off, reconnect and check again. If the message appears again, further assistance may be needed.
Why does my Goodwe GW4600-SS shut down with Insufficient sunlight?
When sunlight is insufficient, the Goodwe PV Inverter may continuously start up and shut down automatically due to insufficient power generated by the PV panel. If the problem remains, further assistance may be needed.
Essential safety guidelines for installation, operation, and maintenance.
Procedures and considerations for securely mounting the inverter.
List of included accessories and initial inspection of the inverter.
Detailed steps for installing the inverter unit.
Guidelines for connecting the inverter to AC and DC power sources.
Table of error messages and their corresponding solutions for troubleshooting.
Description of the inverter's operating panel and status indicator lights.
Explanation of the LCD display, its areas, and key operation for menu navigation.
List of system error messages and descriptions for fault diagnosis.
Procedure for resetting the inverter's wireless monitoring ID.
Technical specifications for GW1500-SS, GW2000-SS, and GW3000-SS models.
Technical specifications for GW4000-SS and GW4600-SS models.
Technical specifications for GW3600S-DK/UK model.
Details on the standard warranty period and requirements for the warranty card.
Conditions for warranty service and situations where warranty is not valid.
General| Model | GW4600-SS |
|---|---|
| Max. Output Current | 20A |
| Rated Output Voltage | 230V |
| Output Voltage | 230V |
| AC Voltage Range | 180-280V |
| Rated Grid Frequency | 50/60Hz |
| Frequency | 50/60Hz |
| Total Harmonic Distortion (THD) | <3% |
| Protection Degree | IP65 |
| Cooling Method | Natural convection |
| Rated Power | 4600W |
| Max. Input Current per MPPT | 12A |
| Rated AC Output Power | 4600W |
| Max. AC Apparent Power | 4.6kVA |
| Power Factor | 0.8 leading - 0.8 lagging |
| DC Injection Current | <0.5% of rated output current |
| Operating Temperature Range | -25°C to 60°C |
| Operating Temperature | -25°C to 60°C |
| Protection Class | Class I |
| Cooling Type | Natural convection |
To Next Page
