Why is the flow reading inaccurate on my Graco Measuring Instruments?
If you're getting inaccurate flow readings on your Graco Measuring Instruments, the flow meter sensor or the meter itself may be faulty and require replacement. Another cause could be that the meter needs calibration.
What to do if the pressure or flow rate reads 0 when fluid is flowing on Graco Measuring Instruments?
If the pressure or flow rate reads 0 on your Graco Measuring Instruments when fluid is flowing, the flow meter or pressure transducer cable might be loose or disconnected. Check the digital input/output cable going to or from the meter to resolve this.
How to troubleshoot inaccurate pressure range in Graco Measuring Instruments?
If you're experiencing an inaccurate pressure range with your Graco Measuring Instruments, it could be due to selecting the wrong transducer. Ensure the correct transducer is chosen. Also, review and correct the settings for the pressure offset (mV) and slope (mV/bar).
What causes fluid not flowing in Graco Measuring Instruments?
If fluid is not flowing in your Graco Measuring Instruments, it may be due to clogs in the fluid line or meter. Clean the fluid line and/or meter. Another cause could be worn or damaged gears.
What to do if higher fluid pressure cannot be achieved with Graco Measuring Instruments?
If higher fluid pressure cannot be achieved with your Graco Measuring Instruments, check the incoming system air pressure and incoming fluid pressure from the pump. Also, check I/P pilot line output pressure and power output of the barrier that powers the system.
What causes low flow in Graco Measuring Instruments?
Low flow in your Graco Measuring Instruments may be due to inadequate air supply through the I/P transducer. Try increasing the incoming air pressure.
How to fix a completely dark Graco Measuring Instruments ProControl 1KE Plus?
If your Graco Measuring Instruments ProControl 1KE Plus is completely dark, first ensure that the power supply is turned on. If the power is on, check for loose or disconnected power cables and tighten or reconnect them.
What to do if Graco Measuring Instruments ProControl 1KE Plus has power but does not function?
If your Graco Measuring Instruments ProControl 1KE Plus has power but isn't functioning, it may be due to a hardware failure, requiring replacement of the ProControl 1KE Plus.
How to fix communication failure in Graco Measuring Instruments?
If you are experiencing a communication failure with your Graco Measuring Instruments, check the address configuration, communication parameters, cabling, and wiring.
Why does Graco Measuring Instruments pressure or flow rate read “— — —” all the time?
If the pressure or flow rate on your Graco Measuring Instruments consistently reads “— — —”, it indicates that the units in Setup are set to NONE, meaning the system recognizes no pressure transducer or fluid meter. Choose preferred units for each device present.
Read all warnings and instructions in this manual and save them.
Details on hazardous location approval for North America and Europe.
Precautions to prevent fire and explosion from flammable fumes.
Conditions for safe use related to isolation and grounding.
Instructions for grounding and preventing electric shock.
Guidelines for installing intrinsically safe equipment in hazardous locations.
Risks associated with pressurized fluid and leaks.
Consequences of operating equipment improperly or under influence.
Recommended PPE for preventing injury in the work area.
Guidelines for installing intrinsically safe components and systems.
Instructions for making electrical connections as per control drawing.
Importance of grounding to reduce risks of static and electric shock.
Identification and description of ports on DCM and ADCM units.
Procedure for updating DCM or ADCM software using Manual 3A1244.
Procedure and precautions for replacing the unit's battery.
Interpreting LED signals for system status and errors.
List and visual identification of DCM and ADCM module and bracket parts.
Important notes and requirements for installing intrinsically safe systems.
Entity parameters for Fiber Optic Receiver and Transmitter ports.
Entity parameters for CAN Data/Power input and output barriers.
Entity parameters for Digital I/O A output barriers.
Entity parameters for Differential Analog Input A.
Entity parameters for 4-20 mA Output A.
Entity parameters for 4-20 mA Output B.
Entity parameters for Differential Analog Input B.
Contact information and website for Graco products and support.
General| Brand | Graco |
|---|---|
| Model | 24L097 |
| Category | Control Unit |
| Language | English |
To Next Page
