HIGH
PRESSURE SPRAY
CAN
CAUSE SERIOUS INJURY.
FOR
PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS.
Read and understand all instruction manuals before operating equipment.
FLUID
INJECTION
HAZARD
General
Safety
This equipment generates very high fluid pressure. Spray from
the gun, leaks or ruptured components can inject fluid
through your skin and into your body and cause extremely
serious bodily injury, including the need for amputation. Also,
fluid injected or splashed into the eyes or on the skin can
cause
serious damage.
NEVER point the spray gun at anyone or at any part of the
try to
"
blow back
"
paint: this is NOT an air spray system.
body. NEVER put hand or fingers over the spray tip. NEVER
ALWAYS have the tip guard in place on the spray gun when
spraying.
..
.
before
cleaning or removing the spray tip or servicing any
ALWAYS follow the Pressure Relief Procedure, below,
system equipment.
NEVER try to stop or deflect leaks with your hand or body.
Be sure equipment safety devices are operating properly
before each use.
If
any fluid appean to penetrate your skin, get EMERGENCY
Medlcal
Alert
-
Airless
Spray
Wounds
SIMPLE CUT. Tell the doctor exactly what fluid was injected.
MEDICAL CARE AT ONCE. DO NOT TREAT AS
A
Spray
Gun
Safety Devices
Be sure all gun safety devices are operating properly before
can cause a malfunction and result in serious bodily injury.
each use. Do not remove or modify any part of the gun; this
Safety
Latch
the gun safety latch in the closed
or
"
safe
"
position, making
Whenever you stop spraying, even for a moment, always set
the gun inoperative. Failure to set the safety latch can result in
accidental triggering of the gun.
DHuser
The gun diffuser breaks up spray and reduces the risk
of
fluid
injection when the
tip
is not installed. Check diffuser operation
regularly. Follow the Pressure Relief Procedure, below,
then remove the spray
tip.
Aim the gun into
a
metal pail,
holding the gun firmly to the pail. Using the lowest possible
to an irregular stream, replace
the diffuser immediately.
pressure, trigger the gun. If the
fluid emitted
is
not
diffused in-
Tip
Guard
ALWAYS have the tip guard
in
place
on
the spray gun while
spraying. The
tip
guard alerts you to the fluid injection hazard
and helps reduce,
but
does not prevent, the risk of accidental-
spray
tip.
ly Placing your fingers or any part of your body close to the
Spray
Tip
Safetv
Note
to
Physician:
lnjectiofl
in the
skin
is
a
tr.9UfnetiC
in-
the spray tip clogs while spraying, engage the
gun
safety latch
Use extreme caution when cleaning or changing spray tips. If
iuV.
It
IS
Important to treat the lnjuWsIJr€llcellv
08
soon immediately. ALWAYS follow
the
Pressure Relief
Pro-
as
posslble.
Do
not delay treatment
to
reseerch
toxicity.
Toxicity is e concern with some exotic coatings injected
cedure and then remove the spray tip to clean it.
surgeon or reconstructive hand
surgeon
mey
be advisable.
fully relieved and the gun safety latch is engaged.
direct&'
into
the blood
Stream.
COflSUltetiOn wirh
8
Pl8SfiC
NEVER wipe
off
build-up around the spray tip
until
pressure is
Pressure
Relief
Procedure
TO reduce the risk of serious bodily injury, including
fluid
injection, splashing fluid or solvent
in
the eyes or on the skin, or injury
from moving Parts or electric shock, alwap follow this procedure whenever you shut off the sprayer, when checking or se~yic-
ing
any Part
Of
the spray Wtem, when installing, cleaning or changing spray tips, and whenever you stop spraying.
(I
J
Engage
the
un
Safety latch.
(2)
Turn the
ON/OFF
switch to
OFF.
(3)
Unplug the power supply cord.
(4)
Disengage the gun SafeW latch.
gun
MfeW latch.
17)
Open the drain valve/pressure relief ValVe. having a container ready to catch the drainage.
(8)
Leave the
6)
&Id
metal Part
of
the gun firmly to the side of a grounded metal pail, and trigger the gun to relieve pressure.
(6)
Engage
the
drain valve/pressure
relief valve open
until
you ere ready to spray again,
If
you
suspect that the sprey
tip
or hose is completetY clogged, or that pressure has
not
been fu/& relieved after fo//owjng the
stepsabove,
VERY
SLOWLY loosen the
tip
guard retaining nut
or
hose end coupling and relieve pressure gradually,jhen loosen
completely. Now clear the tip or hose.
ENG
A
GE
SAFETY
TURN SWITCH AND TRIGGER GUN: OPEN DRAIN VALVE
OR
DISENGAGE SAFETY
UNPLUG
COR0
TO OFF
ENGAGE SAFETY AGAIN PRESSURE RELIEF VALVE
To Next Page
Loading...
Need help?
General
