GRAUPNER mc-32 - Page 145

324 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

145

For your notes

Table of Contents

General Notices Table of Contents2
- Table of Contents2
- Environmental Protection Notices3
- Safety Notices4
- Safety Notices and Handling Regulations for Lithium-Ion (Liio) and Lithium-Polymer (Lipo) Batteries7
- Foreword10
- Remote Control Set Description11
- Technical Data14
- General Operating Notices Transmitter16
  - Opening the Transmitter Housing16
  - Transmitter Power Supply16
  - Recommended Chargers17
  - Battery Operation Timer in Display18
  - Lithium Battery, CR 203218
  - Joystick Length Adjustment18
  - Joystick Conversions19
  - Holder Bracket for Transmitter Straps20
  - Installing Additional Controls, Switches, Etc20
  - Aligning the Antenna20
  - Transmitter Description Front Side21
- Commissioning the Transmitter42
  - Firmware Update Via PC43
- Commissioning the Receiver46
  - Receiver System Power Supply47
  - General Charging Notices49
  - Firmware Update50
- Installation Notices52
- Term Deﬁ Nitions54
- Assigning Transmitter Controls, Switches and Control Switches56
- Digital Trim58
- Winged Models60
  - Receiver Layout61
- Helicopter Models64
  - Receiver Layout65
- Loading a New Memory Location66
- Model Select69
- Copy / Erase70
  - Erase Model70
  - Copy Model  Model70
  - Export to SD Card71
  - Import from SD Card72
  - Copy Fl Ight Phase72
  - Changes73
- Suppress Codes74
- Suppress Models75
- Basic Settings, Model76
  - Binding Receivers77
  - Range Test80
  - Helicopter Model84
    - Binding Receivers85
    - Range Test88
- Model Type94
- Helicopter Type98
- Servo Adjustment102
- Stick Mode104
  - Helicopter Model106
- Control Adjust108
  - Helicopter Model112
- Dual Rate / Expo120
  - Helicopter Model124
- Channel 1 Curve128
  - Winged Model128
  - Helicopter Model131
- Switch Display134
- Control Switch135
- Logical Switches138
  - How Do I Program a Fl Ight Phase140
- Phase Settings142
  - Helicopter Model146
- Phase Assignment148
- Phase Trim« (Winged Model)150
- Non-Delayed Channels151
- Timers (General)152
- Timers156
  - What Is a Mixer159
- Wing Mixers160
  - Aileron163
  - Aileron and 1 Camber Fl Ap164
  - Ailerons166
  - 2/4 Ailerons and 1/2/4 Camber Fl Aps168
Helicopter Mixer176
- Adjusting the Throttle and Pitch Curve187
- Autorotation Setting190
- General Remarks about Freely Progr. Mixers192
Free Mixers193
- Linear Mixers197
- Exponential Mixers199
- Examples201
MIX Active/Phase204
MIX Only Channel205
Dual Mixer206
Swashplate Mixer208
Fail Safe208
Teacher/Pupil210
- Connection Schematic213
- Wireless Hott System214
Transmitter Output218
Proﬁ -Trim220
- Winged Model220
- Helicopter Model222
Trim Memory224
- Winged Model224
- Trim Memory Winged Model224
- Helicopter Model226
Telemetry228
- Setting & Dataview229
  - Satellite Mode of Two Receivers238
  - Sensor/S239
- Selecting Sensors240
- RF Status View241
- Select Voice Update242
Channel Sequence244
Multichannel246
Ring Limiter250
MP3-Player254
General Basic Settings256
Servo Display262
Servo Test263
Code Lock264
Info Display266
Programming Examples Introduction268
- Winged Model First Steps270
- Helicopter Model308
Appendix Fcc Declaration318
- Fcc Information318
- Conformity Declaration319
- Guarantee Certiﬁ Cate320

Other manuals for GRAUPNER mc-32

Manual345 pages

Related product manuals

GRAUPNER mc-32 HoTT

Preview: GRAUPNER Kingpad mc-32 Edition

GRAUPNER Kingpad mc-32 Edition

Preview: GRAUPNER MC-32EX

GRAUPNER MC-32EX

Preview: GRAUPNER mc-16

Preview: GRAUPNER MC-28

Preview: GRAUPNER mc-26

Preview: GRAUPNER MC-20 HoTT

GRAUPNER MC-20 HoTT

GRAUPNER HoTT MC-20 Series

Preview: GRAUPNER HoTT MC-16 Series

GRAUPNER HoTT MC-16 Series

Preview: GRAUPNER mz-24 PRO

GRAUPNER mz-24 PRO

Preview: GRAUPNER MX-12 - PROGRAMMATION

GRAUPNER MX-12 - PROGRAMMATION