EasyManua.ls Logo

Gree VERSATI SERIES - UNITS MAINTENANCE

Gree VERSATI SERIES
158 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
96
Air to Water Heat Pump
Service Manual- Versati Series
JOTUBMMBUJPO
4
321
OFF
NC
2 way value 1
2 way value 2
NC
NO
NO
OFF
ON
ON
N
N
N
N
5
6
WARING!
ķ
Normal Open type should be connected to wire (NO) and wire (N)for valve closing in cooling mode.
ĸ
Normal Closed type should be connected to wire (NC) and wire (N)for valve closing in cooling mode.
(NO) : Line signal (for Normal Open type) from PCB to 2-way valve
(NC) : Line signal (for Normal Closed type) from PCB to 2-way valve
(N) : Neutral signal from PCB to 2-way valve
2.3.8 3-Way Valve
ZD\YDOYHLVUHTXLUHGWRRSHUDWHVDQLWDU\ZDWHUWDQN5ROHRIZD\YDOYHLVÀRZVZLWFKLQJEHWZHHQXQGHU
ÀRRUKHDWLQJORRSDQGZDWHUWDQNKHDWLQJORRS
General Information
Type Power Operating Mode Supported
SPDT
3-wire
230V 50Hz ~AC
230V 60Hz ~AC
Selecting “Flow A” between “Flow A” and “Flow B” Yes
Selecting “Flow B” between “Flow B” and “Flow A” Yes
(1). SPDT = Single Pole Double Throw. Three wires consist of Live1 (for selecting (for selecting Flow B),
and Neutral (for common).
(2). )ORZ$PHDQVµZDWHUÀRZIURPWKHLQGRRUXQLWWRXQGHUÀRRUZDWHUFLUFXLW¶
(3). )ORZ%PHDQVµZDWHUÀRZIURPWKHLQGRRUXQLWWRVDQLWDU\ZDWHUWDQN¶
How to Wire 3-Way Valve:
Follow below procedures Step 1 ~ Step 2.
Step 1. Uncover front cover of the indoor unit and open the control box.
Step 2. Find terminal block and connect wire as below.
12
1110
7
8
9
3 way value 1 3 way value 2
ONOFF
OFF
N
ON
N
WARING!
ķ
3-way valve should select water tank loop when electric power is supplied to wire (OFF) and wire (N).
ĸ
ZD\YDOYHVKRXOGVHOHFWXQGHUÀRRUORRSZKHQHOHFWULFSRZHULVVXSSOLHGWRZLUH21DQGZLUH1
(OFF) : Line signal (Water tank heating) from PCB to 3-way valve
21/LQHVLJQDO8QGHUÀRRUKHDWLQJIURP3&%WRZD\YDOYH
(N) : Neutral signal from PCB to 3-way valve
2.3.9 Gate-controller
If there is gate control function, pull out the leading wire 50 on terminal board(XT2) between19 and 20 or
between 21 and 22, and then connect the Gate-controller .
Installation Guide follow as:
(1). GRS-CQ6.0Pd/Na-K(I), GRS-CQ8.0Pd/Na-K(I), GRS-CQ10Pd/Na-K(I), GRS-CQ12Pd/Na-K(I), GRS-
CQ14Pd/Na-K(I), GRS-CQ16Pd/Na-K(I), GRS-CQ12Pd/Na-M(I), GRS-CQ14Pd/Na-M(I), GRS-
CQ16Pd/Na-M(I)
1920
Gate-controller
GREE does not supply
this section
1920
50
XT
XT

Related product manuals