EasyManua.ls Logo

GreenWorks GPW1804CK User Manual

GreenWorks GPW1804CK
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Missing parts, accessories or need a service center?
Do Not Return to Store
Call : 1-888-909-6757
www.GreenWorksTools.com
INSTALLING DETERGENT BOTTLE
Insert the male end of the bottle into the female outlet on the
trigger handle.
While pushing in the bottle firmly, turn clockwise until tabs lock
into place to ensure a leak-free connection.
Unscrew the bottle from the assembly and fill with pressure
washer detergents/soaps only.
Connect garden hose to pressure
washer water intake.
Assemble pressure washer gun to spray
wand.
Insert the uberflex hose into trigger
handle.
Turn on water at outlet.
Run water hose for 30 seconds with the
motor in OFF position. This helps drain air
from the tank and lines.
Connect power cord to wall outlet
Extension cord not recommended.
Turn on Pressure Washer
IMPORTANT: Ensure water outlet is On
before turning power On to avoid damage
to the pump.
NOTE:
AUTO ON/OFF SWITCH: This Pressure washer is equipped
with an Auto Start/Stop feature.
To operate: Turn the power switch to the On (I) position. Pump will
pressurize and shut down immediately.
Once the trigger of the gun is depressed the unit will turn on.
Unit will shut off and be in standby mode when trigger is released.
1800 PSI / 1.1 GPM
ELECTRIC PRESSURE WASHER
GPW1804CK
This Quick Start Guide is not a substitute for reading the operator's manual. To reduce the risk
of injury or death, user must read and understand operator's manual before using this product.
WARNING:
Set-up
Connect the uberflex hose to the
pressure washer gun assembly by turning
the fitting clockwise. Ensure the fitting is fully
tightened to the pressure washer gun.
Insert the male end (A) of the wand
into the female bayonet outlet (B)
firmly.
While pushing in the wand firmly, turn
clockwise until tabs lock into place to
ensure a leak-free connection.
Pull back the quick-connect collar
Push the spray tip into place
Push the collar forward
Insert the uberflex hose into the pressure
washer.
1
4
5
8
30S
6
A
B
2
3
SPRAY TIP
APPLICATION
40
O
White - Wide fan tip (40° )
The white 40 degree tip, referred to as the “fan” tip creates the widest
area of cleaning with relatively low pressure. This pressure washer tip is
best used for light or delicate cleaning applications. It is recommended
for light cleaning on wood decks and other soft or delicate surfaces.
TURBO
Turbo Nozzle Tip
This nozzle rotates in a zero to 15 degree circular motion spray pattern
to break down tough dirt and grime. The spray pattern can cover area of
4 to 8 inches wide, depending on the distance between the tip and the
1
2
3
surface being cleaned.
77
Question and Answer IconNeed help?

Do you have a question about the GreenWorks GPW1804CK and is the answer not in the manual?

GreenWorks GPW1804CK Specifications

General IconGeneral
Power SourceElectric
Pressure1800 PSI
Flow Rate1.1 GPM
Motor13 Amp
Hose Length20 feet
Spray Tips0°, 15°, 25°, 40°

Summary

Pressure Washer Setup Guide

Connect Hoses and Wand

Connect uberflex hose to gun, wand to gun, and then hoses to the pressure washer.

Prepare for Operation

Turn on water, flush system for 30 seconds, and connect power cord.

Power On Pressure Washer

Turn on the pressure washer, ensuring water is supplied to prevent pump damage.

Detergent Bottle Installation

Fill and Connect Detergent Bottle

Fill the bottle with detergent, attach it to the trigger handle, and secure it clockwise.

Spray Tip Applications

Wide Fan Tip (40°)

Provides a wide cleaning area at low pressure, suitable for light or delicate surfaces.

Turbo Nozzle Tip

Rotates for a circular pattern to remove tough dirt and grime from surfaces.

Related product manuals