Grizzly G1021Z User Manual (English)

Other manuals for Grizzly G1021Z

Questions and Answers:

O
omannAug 18, 2025
What to do if my Grizzly Planer motor stalls and blows fuses?
- B
  Brittany CampbellAug 19, 2025
  If your Grizzly Planer motor stalls, resulting in blown fuses or a tripped circuit, the possible causes are: a short circuit in the motor or loose connections, low voltage, incorrect fuses or circuit breakers in the power line, or the motor is overloaded. To resolve this: Inspect the connections on the motor for loose or shorted terminals or worn insulation. Correct any low voltage conditions. Install the correct fuses or circuit breakers. Reduce the load on the motor.
J
Jennifer GuerreroAug 21, 2025
Why does my Grizzly G1021Z motor overheat?
- J
  Jonathan RayAug 21, 2025
  Your Grizzly Planer motor may overheat due to being overloaded or restricted air circulation. Reduce the load on the motor. Clean the motor to allow normal air circulation.
S
Steven SmithAug 23, 2025
What to do if my Grizzly Planer machine is loud when cutting, overheats, or bogs down?
- R
  Richard MurphyAug 23, 2025
  If your Grizzly Planer is loud when cutting and overheats or bogs down, it could be due to an excessive depth of cut or dull knives. Decrease the depth of cut and sharpen the knives.
J
James StaffordAug 26, 2025
Why is my Grizzly G1021Z machine slowing down?
- B
  Brandon WardAug 26, 2025
  If your Grizzly Planer slows down during operation, it could be because the feed rate is too high, or the depth of cut is too great. Try feeding the workpiece slower or reducing the depth of cut.
B
Brandon ParkerAug 27, 2025
What to do if my Grizzly G1021Z Planer motor will not start?
- J
  Jordan CruzAug 28, 2025
  If the Grizzly Planer motor will not start, the possible causes are low voltage or an open circuit in the motor or loose connections. Check the power line for proper voltage and inspect all lead connections on the motor for loose or open connections.
D
Diane LesterAug 30, 2025
What to do if my Grizzly G1021Z motor won't start and the fuses blow?
- S
  sbakerAug 30, 2025
  If the Grizzly Planer motor will not start and the fuses or circuit breakers blow, the possible causes are: a short circuit in the line cord or plug, a short circuit in the motor or loose connections, or incorrect fuses or circuit breakers in the power line. Inspect the cord or plug for damaged insulation and shorted wires. Inspect all connections on the motor for loose or shorted terminals or worn insulation. Install correct fuses or circuit breakers.
C
Catherine DavisSep 1, 2025
Why is my Grizzly Planer making a loud, repetitious noise?
- K
  kevinmooreSep 2, 2025
  If there's a loud, repetitious noise coming from your Grizzly Planer, it could be due to missing or loose pulley setscrews or keys, the motor fan hitting the cover, or a defective V-belt. Inspect the keys and setscrews, and replace or tighten if necessary. Tighten the fan or shim the cover. Replace the V-belt. See Maintenance.
V
Virginia OrtizSep 3, 2025
What to do if there is chip buildup on the outfeed roller of my Grizzly G1021Z Planer?
- S
  Shaun RiosSep 3, 2025
  If you notice chip buildup on the outfeed roller of your Grizzly Planer, it's likely that chips are working their way back under the chip deflector. To fix this, lay duct tape over the mounting bolts along the outside edge to seal any possible gaps.
E
Elaine OliverSep 6, 2025
Why does my Grizzly Planer howl on startup?
- T
  Timothy PriceSep 6, 2025
  If your Grizzly Planer howls on startup, it's likely that the chip deflector is too close to the cutterhead. Move the chip deflector back 1/8" to 1/4" from the cutterhead.
M
Michael WilsonSep 8, 2025
Why are infeed roller marks left on the workpiece by my Grizzly G1021Z Planer?
- J
  Justin NguyenSep 8, 2025
  If infeed roller marks are left on the workpiece when using your Grizzly Planer, the depth of cut may be too shallow. Increase the depth of cut.