What to do if pan will not tilt on Groen BPM-40GC (Power Tilt Models)?
If the pan on your Groen Commercial Food Equipment (Power Tilt Models) will not tilt, verify that the electrical power supply is on. Check for an overheated actuator motor; if it's overheated, wait 15 minutes for the motor to cool down before operating the power tilt again.
What to do if pilot lights, but main burner will not come on, the spark stays on in Groen Commercial Food Equipment?
If the pilot light on your Groen Commercial Food Equipment is lit, but the main burner won't ignite and the spark remains on, check for improper grounding and repair it with high-temperature wire if needed. Inspect the pilot burner ceramic insulator for cracks. Ensure the high-tension cable isn't grounded out; correct the condition or replace the pilot burner. Verify proper gas pressure. Clean the pilot assembly, or replace it if necessary. Tighten all mechanical and electrical connections and replace the ignition control module.
What to do if pilot lights, but main burner will not come on and spark does not stay on in Groen Commercial Food Equipment?
If the pilot light on your Groen Commercial Food Equipment is lit, but the main burner won't ignite and the spark does not stay on, check the controller to ensure it's closed at a temperature setting higher than the current pan temperature. Verify 24V between terminals MV and ground; if not, replace the ignition control module. Ensure gas pressure is at least 3.5” W.C. (8.7 millibars). Check the electrical connections of the main valve to the terminals and solenoid operation for the main valve on the gas valve, repairing or replacing as necessary. Also, confirm that the secondary thermostat switch is closed.
Why system does not produce a spark in Groen Commercial Food Equipment?
If the system on your Groen Commercial Food Equipment does not produce a spark, check the controller to ensure it is energized. Verify the AC voltage between terminals on the secondary side of the transformer; if it's not 24 volts, replace the transformer. Make sure the high tension cable is in good condition, replacing it if cracked or brittle. Inspect the pilot electric ceramic for cracks or breaks and check/regap the pilot spark gap.
What to do if display not lit on Groen Commercial Food Equipment (Advanced and C2T only)?
If the display is not lit on your Groen Commercial Food Equipment (Advanced and C2T models only), ensure that the power supply is on.
What to check if burners will not light on Groen BPM-40GC?
If the burners on your Groen Commercial Food Equipment won't light, ensure that the main gas supply valve is open (handle in line with the gas pipe). Confirm that the gas supply to the braising pan is at the specified pressure and that the pan body is horizontal.
Why does the main burner come on but will not stay on in my Groen BPM-40GC?
If the main burner of your Groen Commercial Food Equipment ignites but doesn't stay on, inspect the burner ground for damaged wires or loose connections, replacing with high-temperature wire if necessary. Also, check for low gas supply pressure. If the issue persists, consider replacing the ignition control module.
How to fix a Groen BPM-40GC when it does not produce a spark?
If your Groen Commercial Food Equipment isn't producing a spark, check the controller to ensure it's energized. Verify the AC voltage between the terminals on the secondary side of the transformer; if it's not 24 Volts, replace the transformer. Make sure the high tension cable is in good condition; replace it if cracked or brittle. Inspect the pilot electric ceramic for cracks or breaks and check the pilot spark gap, re-gapping if necessary.
What to do if pan will not heat but pilot light is burning in Groen Commercial Food Equipment?
If your Groen Commercial Food Equipment pan will not heat but the pilot light is burning, verify that the secondary thermostat switch is closed.
Why pan stops heating before reaching desired temperature in Groen Commercial Food Equipment?
If your Groen Commercial Food Equipment pan stops heating before reaching the desired temperature, check the temperature controller dial setting and display.
Essential safety guidelines and warnings for operating the braising pan.
Specific instruction to post important information in a visible area for users.
Details the controls for Classic and Advanced braising pan models.
Instructions on how to tilt the pan body using manual or power mechanisms.
List of parts for the braising pan's stand and foot assembly, including casters and feet.
List of replacement parts for the braising pan's cover and counterbalance assemblies.
List of parts for the braising pan's gas piping system, including valves and fittings.
List of parts for the combustion chamber and gas manifold assemblies.
List of electrical components found in the braising pan's trunnion cover area.
List of replacement parts for the manual tilt mechanism of the braising pan.
List of replacement parts for the power tilt system and gas-electronic ignition.
Parts list for converting fuel gas types and orifice quantities for different models.
Wiring schematic for the electronic ignition system in manual tilt models.
Wiring schematic for the electronic ignition system in power tilt models.
Wiring schematic for advanced control manual tilt system.
Wiring schematic for advanced control power tilt system.
Diagram illustrating the standing pilot ignition system of the braising pan.
General| Model | BPM-40GC |
|---|---|
| Category | Commercial Food Equipment |
| Capacity | 40 gallons |
| Power Source | Gas |
| Material | Stainless Steel |
| Description | The Groen BPM-40GC |
To Next Page
