Need help?Do you have a question about the Grundfos CRIE and is the answer not in the manual?
General| Frequency | 50/60 Hz |
|---|---|
| Material | Stainless Steel |
| Flow Rate | Up to 120 m³/h |
| Pumped Liquid | Clean, non-aggressive liquids |
| Voltage | 220-240 V / 380-415 V |
Details pumps lacking a factory-fitted sensor and their control.
Details pumps with a factory-fitted pressure sensor and their control.
Provides safety warnings and guidelines for transporting the product.
Outlines the steps for inspecting the product upon receipt.
Details how to mount the pump securely.
Specifies requirements for cable entry points.
Information on cable glands provided with the pump.
Guidelines for maintaining adequate motor cooling.
Specific considerations for installing the motor outdoors.
Instructions regarding drain holes for moisture management.
Details safety measures for protection against electric shock.
Explains protection against mains voltage transients.
Details the motor's built-in thermal protection.
Specifies requirements for cables used in electrical installation.
Details the required cable cross-sections for power.
Specifies conductor types and temperature ratings.
Details the single-phase voltage and connection requirements.
Details the three-phase voltage and connection requirements.
Explains protection against voltage fluctuations.
Details the automatic overload protection mechanism.
Describes the built-in overtemperature protection.
Covers protection measures against phase unbalance.
Details connection terminals for specific pump models.
Instructions for new bus connection installations.
Guidance for replacing a motor with bus connection.
Specifies the maximum allowed starts and stops per hour.
Details acceptable ambient temperature ranges for operation and storage.
Explains the effect of installation altitude on motor performance.
Introduces the standard and advanced control panels.
Introduces Grundfos GO and R100 remote controls.
Explains how to set the desired setpoint on the control panel.
Shows the pump's operating status indicator.
The main display for the advanced control panel.
Navigational function for the control panel.
Navigation function for menus and settings.
Button to start, stop, and prepare the pump for operation.
Navigational function to return to the main home menu.
Shows user-defined parameters and shortcut access.
Displays pump and system status, warnings, and alarms.
Accesses all detailed pump setting parameters.
Provides assisted setup, control mode descriptions, and fault advice.
Shows when the pump has been stopped by the stop button.
Indicates master pump status in a multipump system.
Indicates slave pump status in a multipump system.
General indicator for multipump system operation.
Shows when settings are disabled for protective reasons.
Lists available parameters and functions in the Home menu.
Lists status information and logs in the Status menu.
Covers settings for pump setpoint configuration.
Settings for pump operating modes.
Settings for various pump control modes.
Settings related to analog input configurations.
Settings for Pt100/1000 temperature sensor inputs.
Settings for digital input configurations.
Settings for signal relay outputs.
Settings for analog output configurations.
Settings for the pump's PI controller parameters.
Settings for the low-flow stop function.
Settings for the pipe filling function.
Settings for the standstill heating function.
Settings for monitoring motor bearing condition.
Setting for the display language.
Settings for configuring date and time.
Settings for unit configuration (SI/US).
Function to enable or disable control panel buttons.
Accesses the log of recorded alarms.
Guided setup procedure for pump configuration.
Provides assistance and advice for pump failures.
Details communication methods between Grundfos GO and the pump.
Overview of the Grundfos GO dashboard interface.
Lists status information available via Grundfos GO.
Settings for pump setpoint configuration via GO.
Settings for pump operating modes via GO.
Settings for pump control modes via GO.
Settings for the pipe filling function via GO.
Settings for the low-flow stop function via GO.
Settings for the pump's PI controller via GO.
Settings for analog input 1 via GO.
Settings for Pt100/1000 inputs via GO.
Settings for digital input 1 via GO.
Settings for pulse flowmeter via GO.
Settings for analog output via GO.
Settings for signal relay 1 via GO.
Accessing the alarm log via GO.
Guided pump setup via GO.
Setup for multipump systems via GO.
Setting the pump's setpoint value.
Describes the different pump operating modes.
Manually setting the pump speed.
Setting a user-defined speed for the pump.
Selection and explanation of pump control modes.
Guided procedure for setting up pump parameters.
Guided setup for analog input configuration.
Sets up alternating operation modes for multipump systems.
Sets up backup operation for multipump systems.
Service information for the motor component.
Service information and documentation for the pump.
Supply voltage and recommended fuse sizes.
Information on leakage current values.
Supply voltage and recommended fuse sizes.
Specifications for digital input characteristics.
Specifications for open-collector digital output characteristics.
Information on electromagnetic compatibility standards.
Sizes and types of cable entries.
Details on supplied cable glands.
Tightening torques for terminals.
Details on the pump's enclosure protection class.
Additional installation instructions for USA and Canada.
Compliance with US and Canadian electrical codes.
Regulatory compliance for radio communication in USA/Canada.
FCC and IC identification numbers for radio modules.
Shows where identification numbers are located on the product.
Refers to cable requirements section.
Maximum tightening torques for terminals.
Specification for line reactor size.
Limit for short circuit current.
Requirements for motor protection fuses.
Requirements for branch circuit breakers.
Internal overload protection degree.
To Next Page
