EasyManuals Logo

Guest Trolling Charger 2613A User Manual

Guest Trolling Charger 2613A
13 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
2
WARNINGS
THIS CHARGER SHOULD BE USED TO CHARGE ONLY LEAD ACID OR GEL
CELL TYPE BATTERIES. USE ON OTHER BATTERY TYPES MAY EXPLODE AND
CAUSE PERSONAL INJURY.
RISK OF EXPLOSIVE GASES! WORKING IN THE VICINITY OF LEAD ACID
BATTERIES IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES
DURING NORMAL OPERATION. THEREFORE IT IS OF THE UTMOST
IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER YOU
FOLLOW THE INSTRUCTIONS EXACTLY.
Personal Safety Precautions
Adhere to the following personal safety precautions when installing or working with the
chargers:
1.
Someone should be within voice range or close enough to come to your aid when
you work near a lead-acid battery.
2.
Have plenty of fresh water and soap nearby in case battery acid contacts skin,
clothing, or eyes.
3.
Wear complete eye protection and clothing protection. Avoid touching eyes while
working near a battery.
4.
If battery acid contacts skin or clothing, wash them immediately with soap and
water. If acid enters the eye, flood the eye with cold, running water for at least ten
minutes and get medical attention.
5.
Never smoke or allow an open flame in the vicinity of the battery.
6.
Do not drop a metal tool onto the battery. It may spark, short circuit the battery and
may cause an explosion.
7.
Remove all personal metal items such as rings, bracelets, necklaces, and watches
when working near a lead-acid battery. A battery can produce short circuit currents
high enough to weld a ring or the like to metal, causing a severe burn.
Preparing to Charge Precautions
Before charging a battery with the charger, read the following precautions:
1.
Do NOT operate the charger if the cables or an LED is damaged.
2.
Make sure all accessories on the product you are charging are OFF.
3.
If the battery or batteries must be removed from the product, always remove the
grounded terminal from the battery first.
4.
Be sure the area around the battery is well ventilated while the battery is being
charged. Gas can be forcefully blown away using a piece of cardboard or other
non-metallic material as a “hand fan”.
5.
Clean battery terminals. Be careful to keep corrosion from coming in contact with
eyes.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Guest Trolling Charger 2613A and is the answer not in the manual?

Guest Trolling Charger 2613A Specifications

2613A

Power Specifications IconPower Specifications
input voltage115 VAC
input voltage options12/24/36 Volts
output amperage5/5/5 Amps
Physical Dimensions IconPhysical Dimensions
size (L x W x H)9.6 x 7 x 2.6 inches
DC cable length6’/4’/4’

2620A

Power Specifications IconPower Specifications
input voltage115 VAC
input voltage options12/24 Volts
output amperage10/10 Amps
Physical Dimensions IconPhysical Dimensions
size (L x W x H)9.6 x 7 x 2.6 inches
DC cable length6’/6’

2623A

Power Specifications IconPower Specifications
input voltage115 VAC
input voltage options12/24 Volts
output amperage10/5/10 Amps
Physical Dimensions IconPhysical Dimensions
size (L x W x H)13 x 7 x 2.6 inches
DC cable length6’/6’/6’

2631A

Power Specifications IconPower Specifications
input voltage115 VAC
input voltage options12/24/36 Volts
output amperage10/10/10 Amps
Physical Dimensions IconPhysical Dimensions
size (L x W x H)13 x 7 x 2.6 inches
DC cable length6’/6’/6’

Related product manuals