To Next PageTo Next Page
Why is no measurement data showing on my Hach Controller?
If no measurement data is showing on your Hach Controller, it is likely because the data log is empty. Measurement data is recorded to the data log in accordance with the selected logging interval.
What to do if some measurements are not showing on the Hach Controller?
Only the measurements recorded to the data log show. To see all the measurements supplied to the sampler by a sensor(s) connected to a sensor port, select Diagnostics>Sensor Ports. To show all the measurements supplied to the sampler by an external instrument(s) that is connected to the AUX I/O port, select Diagnostics>AUX and I/O Port.
How to troubleshoot no instrument power in Hach Laboratory Equipment?
If your Hach Laboratory Equipment has no instrument power, check the following: * Make sure that AC power gets to the electrical outlet. * If you have a refrigerated sampler, the power supply may be defective, so replace the power supply. * If the above steps do not solve the issue, the controller may be defective, so contact technical support.
Why does Hach Laboratory Equipment sampler not have sufficient lift?
If the sampler does not have sufficient lift in your Hach Laboratory Equipment, consider the following: * The strainer may not be completely submerged, so install the shallow depth strainer (2071 or 4652). * The intake tube may have a leak, so replace the intake tube. * The pump tube may be worn, so replace the pump tubing. * The pump roller assembly may be worn, so contact technical support.
What to do if my Hach Laboratory Equipment has no instrument power?
If your Hach Laboratory Equipment has no instrument power, first ensure that AC power is reaching the electrical outlet. If the problem persists, it may be due to a defective controller.
Why is the sample volume incorrect in my Hach Laboratory Equipment?
If the sample volume is incorrect, several factors could be at play: * The volume calibration may be off, so repeat the volume calibration. * The tube length specified in the sampling program may be incorrect, so ensure it is correct. * The intake tube may not be purging completely; ensure it is as vertical and short as possible. * The strainer may not be fully submerged; install the shallow depth strainer (2071 or 4652). * The pump tubing or roller assembly may be worn; replace them as needed. * The liquid detector may be disabled; turn it on and complete a volume calibration. * The liquid detector may not be operating correctly; calibrate it with the sampled liquid.
What to do if the sampler of my Hach Laboratory Equipment doesn't have sufficient lift?
If the sampler does not have sufficient lift, it could be due to several reasons. First, ensure the strainer is completely submerged; if not, install the shallow depth strainer (2071 or 4652). Also, check for leaks in the intake tube and replace it if necessary. Lastly, inspect the pump tube for wear and replace if needed.
Why does "---" show on the Hach Controller Status screen?
If "---" is displayed, it means the measurement is either not currently available or hasn't been recorded yet. The values displayed are the last recorded values, which are saved to the data log based on the chosen logging interval. Ensure that the measurement is being properly supplied to the sampler.
What to do if the red indicator light flashes on my Hach Controller?
The red indicator light flashes when one or more measurements that the sampler is configured to use (such as pH and flow) are unavailable because the corresponding sensor(s) isn't connected. To resolve this, connect the missing sensor to the sampler. Also, verify that the sampler isn't configured to record unavailable sensor measurements to the data log or set up with alarms for sensor measurements that are not available.
Why does no measurement data show on my Hach Controller?
If no measurement data is showing, it's likely because the data log is empty. Remember that measurement data is recorded to the data log according to the selected logging interval.
General| Sample Frequency | Programmable |
|---|---|
| Type | Portable |
| Sampling Method | Vacuum Pump |
| Temperature Control | Refrigerated |
| Bottle Configuration | 24 x 1L bottles |
| Power Supply | 12V DC |
| Communication | RS-232 |
| Sampler Type | Portable or Stationary |
| Vertical Lift | 8.2 m |
| Enclosure Rating | IP67 |
| Number of Samples | Up to 999 |
| Storage Capacity | 24 samples |
| Bottle Options | 1L |
