Haier HW70-12829 User Manual (English)

Questions and Answers:

J
Jacob WilliamsAug 20, 2025
What to do if my Haier HW70-12829 won't start?
- K
  Kimberly FoxAug 21, 2025
  If your Haier Washer isn't starting, it could be due to several reasons: the program might not be started, the door might not be closed properly, the machine might not be switched on, there could be a power failure, or the child lock might be activated. Here's what you can do: Check the program and start it, ensure the door is properly closed, switch the machine on, check the power supply, and deactivate the child lock.
A
Anne SawyerAug 22, 2025
Why is my Haier HW70-12829 vibrating so much during spinning?
- T
  Tyrone AndrewsAug 22, 2025
  Excessive vibration in your Haier Washer during spinning can be caused by a few things: the transportation bolts might not have been removed, the appliance might not be on a solid surface, or the machine load might be incorrect. To fix this, remove all transportation bolts, ensure the washer is on solid, level ground, and check the load weight and balance.
A
angelalewisAug 25, 2025
What to do if my Haier HW70-12829 isn't draining properly?
- J
  John RobbinsAug 25, 2025
  If your Haier Washer is experiencing drainage failure, it could be because the drain hose is blocked, the pump filter is blocked, or the drain hose end is higher than 100 cm above the floor level. You should unblock the drain hose, clean the pump filter, and ensure that the drain hose is properly installed.
D
Drew RyanAug 26, 2025
Why is my Haier HW70-12829 Washer not spinning?
- K
  Kathryn SmithAug 27, 2025
  If your Haier Washer isn't spinning, it's likely due to an unbalance of laundry. Check the machine load and laundry, and then run a spinning program again.
E
Eric FrenchAug 27, 2025
Why is my Haier Washer not filling with water?
- J
  Julie MorganAug 27, 2025
  Your Haier Washer might not be filling with water due to several reasons: there may be no water supply, the inlet hose could be kinked or blocked, the water pressure might be too low, the door might not be properly closed, or there could be a water supply failure. To resolve this, check the water tap, inspect the inlet hose for kinks or blockages, unblock the inlet hose filter, verify the water pressure, ensure the door is properly closed, and confirm the water supply is working.
M
Mark HamiltonAug 29, 2025
Why does my Haier HW70-12829 keep draining while filling?
- R
  Roy StricklandAug 30, 2025
  If your Haier Washer is draining while it's filling, it's likely because the drain hose is not properly installed or the drain hose end is reaching into the water. Ensure that the drain hose is properly installed and is not in water.
K
Karen HudsonAug 31, 2025
Why does my Haier HW70-12829 Washer stop mid-cycle?
- T
  Tanya ByrdAug 31, 2025
  If your Haier Washer stops before completing the wash cycle, it is likely due to a water or electric failure. Check the power and water supply.
W
wwolfeSep 2, 2025
What to do if my Haier Washer stops for a while during the cycle?
- P
  petersenjamesSep 2, 2025
  If your Haier Washer stops for a period of time during the cycle, it could be due to several reasons: the appliance might be displaying an error code, there might be a problem due to the load pattern, or the program might be performing a soaking cycle. Consider display codes, reduce or adjust the load, or cancel the program and restart it.
T
taylorjillSep 4, 2025
Why is there so much foam in my Haier HW70-12829?
- C
  Christine MurphySep 4, 2025
  Excessive foam in your Haier Washer is usually caused by using an inappropriate detergent or using too much detergent. Check the detergent recommendations and reduce the amount of detergent you're using.
K
Kayla LeeSep 5, 2025
Why is the washing time changing on my Haier HW70-12829?
- T
  Trevor BooneSep 5, 2025
  The washing programme duration on your Haier Washer will be adjusted automatically. This is normal and doesn‘t affect functionality.