HANYOUNG NUX ML-D Series - Page 31

29
Before staring Installation Operation Specifications
Register address (HEX) Symbol
Description
Property
(R/W)
Setting range Unit
Initial
value
CH1 CH2 CH3 CH4
n : Number
of channel
86(56) PRS
Communication
protocol
R/W
0 : PC-LINK
1 : PC-LINK with SUM
2 : Modbus ASCII
3 : Modbus RTU
ABS
0 (PC-
LINK)
87(57) BPS
Transmission
speed (Bit per
second)
R/W
0 : 9600 bps
1 : 19200 bps
2 : 38400 bps
3 : 57600 bps
4 : 76800 bps
ABS
0 (9600
bps)
88(58) PRI Parity bit R/W
0 : NONE
1 : ODD
2 : EVEN
ABS
2
(EVEN)
89(59) STP Stop bit R/W
1 : 1 Bit
2 : 2 Bit
ABS 1 (1 Bit)
90(5A) DLN Data length R/W
7 : 7 Bit
8 : 8 Bit
ABS 8 (8 Bit)
91(5B) RPT
Communication
response delay
R/W
0~10 delay time= process time
(maximum 25ms) +RTP X 10ms
ABS 0
95(5F) ADDR
Communication
setup Address
R 1 ~ 32 ABS -
96(60) MAX_CH
Number of
channels
R 4 : 4 Channel ABS -
97(61) R_SYS System data R - ABS -
98(62) R_OPT Option data R - ABS -
99(63) ROMVER Firmware version R - ABS -
101
(65)
201
(C9)
301
(12D)
401
(191)
PV Process value R EU (0 ~ 100%) ℃ -
102
(66)
202
(CA)
302
(12E)
402
(192)
SV Set value R/W EU (0 ~ 100%) ℃ EU (0%)
103
(67)
203
(CB)
303
(12F)
403
(193)
MV Manipulated Value R 0.0 ~ 100.0 % 0
104
(68)
204
(CC)
304
(130)
404
(194)
CHSTS Channel status R
All error status OR run
15 Bit: Set “1” at System Data error
14 Bit: Set “1” at Calibration Data error
13 Bit: Set “1” at input circuit error
12 Bit: Set “1” at EEPROM error
11 Bit: Set “1” after 24 hours of auto toning (AT)
10 Bit: Set “1” at standard contact point
correction (RCJ) error
9 Bit: Set “1” when exceeding ±5% input range
8 Bit: Set “1” at input sensor error (B. OUT)
2 Bit: Set “1” at auto tuning (AT) run
1 Bit: Set “1” at monitor mode
0 Bit: Set “1” at run start
ABS -
105
(69)
205
(CD)
305
(131)
405
(195)
EVSTS
Event channel
by channel 1~8
status
R
All events OR run
7 Bit(128): Set “1” at event channel 8 occurrence
6 Bit(64): Set “1” at event channel 7 occurrence
5 Bit(32): Set “1” at event channel 6 occurrence
4 Bit(16): Set “1” at event channel 5 occurrence
3 Bit(8): Set “1” at event channel 4 occurrence
2 Bit(4): Set “1” at event channel 3 occurrence
1 Bit(2): Set “1” at event channel 2 occurrence
0 Bit(1): Set “1” at event channel 1 occurrence
ABS -
106
(6A)
206
(CE)
306
(132)
406
(196)
OUTSTS Output status R
0: output (OFF)
1: output (ON)
ABS -