Harman Kardon AVR147 User Manual

3. Disconnect the lead wire (BN84-5P) on the Fip PCB (37-1) from connector (CN84) on the Volume PCB (37-6).
4. Disconnect the lead wire (BN85-3P) on the Fip PCB (37-1) from connector (CN85) on the Phone PCB (37-5).
5. Disconnect the lead wire (BN88-4P) on the Fip PCB (37-1) from connector (CN88) on the Power Led PCB (37-3).
6. Disconnect the connector (CN89) on the Fip PCB (37-1) from lead wire (BN89-4P) on the Key PCB (37-2).
7. Remove 3 screws (S2) and then remove the Guide PCB (37-8) & the Fip PCB (37-1).
7 KEY PCB (37-2) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1.
2. Remove the Front Panel ASS’Y, referring to the previous step 2.
3. Remove the Fip PCB (37-1), referring to the previous step 6.
4. Remove 10 screws (S2) and then remove the Key PCB (37-2).
8 TUNER MODULE (44) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1.
2. Disconnect the card cable between connector (CON1-13P) on the Tuner module (42) and connector (CN13) on the
Input PCB (39-1).
3. Remove 2 screws (S8) and then remove the Tuner Module (43).
9 VIDEO PCB (41) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1.
2. Disconnect the card cable between connector (BN14-13P) on the Video PCB (41) and connector (CN14) on the Input
PCB (39-1).
3. Disconnect connector (CN43) on the Video PCB (41) from the lead wire (BN43-3P) on the Regulator PCB (A)(40-2).
4. Disconnect the card cable between connector (CN42) on the Video PCB (41) and connector (BN44-7P) on the iPod
PCB (39-2).
5. Disconnect connector (CN41) on the Video PCB (41) from the lead wire (BN41-6P) on the Volume PCB (37-6).
6. Remove 6 screws (S8) and then remove the Video PCB (41).
10 iPod PCB (39-2) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1.
2. Remove the Video PCB (41), referring to the previous step 9
3. Disconnect the card cable between connector (BN19-15P) on the the iPod PCB (39-2) and connector (CN19) on the
Input PCB (39-1).
4. Disconnect the card cable between connector (BN44-7P) on the iPod PCB (39-2) and connector (CN42) on the Video
PCB (41).
5. Disconnect the card cable between connector (CN47-7P) on the iPod PCB (39-2) and connector (CN47) on the
RS232 PCB (37-7).
6. Disconnect the board to board connector between and connector (CN23) on the XM PCB (42) and connector (BN17-
12P) on the iPod PCB (39-2).
7. Remove 2 screws (S13) and then remove the iPod PCB (39-2).
11 XM PCB (42) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1.
2. Remove the Video PCB (41), referring to the previous step9.
3. Disconnect the card cable between connector (BN21-7P) on XM PCB (42) and connector (CN21) on the input PCB
(39-1).
4. Disconnect the lead wire (BN85-2P) on the XM PCB (42) from connector (CN85) on the Regulator PCB (A)(40-2).
34
AVR147 harman/kardon

Harman Kardon AVR147 Specifications

General

Brand	Harman Kardon
Model	AVR147
Category	Receiver
Language	English