Hayward XE Series User Manual (English)

Other manuals for Hayward XE Series

Questions and Answers:

J
Joseph StewartAug 20, 2025
Why is there low flow in my Hayward Water Pump?
- S
  Susan NguyenAug 20, 2025
  Low flow in your Hayward Water Pump can stem from several issues. Air leaks in the suction line can cause bubbles at the return fittings; re-tighten suction and discharge connections with PTFE tape and inspect other plumbing. Other possible causes include undersized pool piping (correct the piping size), or a plugged, restricted, or damaged impeller (replace the impeller including a new seal assembly).
M
Mary PerezAug 22, 2025
What to do if my Hayward Water Pump has stalled?
- S
  stacey25Aug 23, 2025
  If your Hayward Water Pump has stalled, check the impeller, diffuser, shaft seal, and motor for any issues or binding.
D
Daniel PierceAug 26, 2025
What to do if the motor current is too high in my Hayward XE?
- J
  Jessica WilliamsAug 26, 2025
  If the motor current is too high in your Hayward Water Pump, check the impeller, diffuser, shaft seal, and motor for any issues or binding.
E
Elizabeth HernandezAug 28, 2025
What to do if my Hayward Water Pump motor will not start?
- H
  hernandezalanAug 28, 2025
  If your Hayward Water Pump motor won't start, begin by checking the wiring against the diagrams. Ensure the pump is correctly wired for the available voltage/current according to the data nameplate. Inspect for any loose or improper wiring, open switches or relays, tripped circuit breakers, or blown fuses, and correct them. Manually check the motor shaft for any obstructions, ensuring it rotates freely.
J
John CannonAug 31, 2025
Why is my Hayward XE Water Pump so noisy?
- H
  Hannah HansonAug 31, 2025
  A noisy Hayward Water Pump can be due to several reasons. Check for air leaks in the suction piping, which can cause cavitation, or restrictions/undersizing in the suction line. Low water levels in the pool or unrestricted discharge return lines can also contribute. Ensure the pump is mounted on a level surface and securely fastened. Foreign matter in the pump housing could also be the culprit. Also, motor bearings can become noisy due to wear, rust, overheating, or chemical exposure, leading to seal damage and water seepage. Replace seal leaks immediately.
W
webercharlesSep 2, 2025
What to do if my Hayward XE Water Pump motor shuts OFF and the LED is not Solid ON?
- A
  Anthony GomezSep 3, 2025
  If your Hayward Water Pump motor shuts off and the LED isn't solid, it's frequently caused by undersized wiring. Check for low voltage or power drops at the motor. Contact a qualified professional to verify the electrical connections.
M
Mr. Jeremy KelleySep 5, 2025
What to do if my Hayward XE Water Pump motor hums, but does not start?
- B
  Brad AguilarSep 5, 2025
  If your Hayward Water Pump motor hums but doesn't start, it could be that the impeller is jammed with debris. Have a qualified repair professional open the pump and remove the debris.
S
Shawn CuevasSep 7, 2025
What does it mean if the IPM temperature is too high in my Hayward Water Pump?
- D
  Derek ClarkSep 7, 2025
  If the IPM temperature is too high in your Hayward Water Pump, the motor airflow path should be checked for obstructions and cleared if present. Also, check the ambient temperature and compare it against the motor nameplate specifications.
J
Joel HarperSep 12, 2025
What does it mean if the DC voltage is out of range in my Hayward XE?
- T
  thomasthomasSep 12, 2025
  If the DC voltage is out of range in your Hayward Water Pump, verify that the line voltage is within 10% of the pump's rated voltage at the terminal block. Also, ensure that power supply connections are properly made at the circuit breaker and terminal block, and that the voltage change jumper is correctly set for the intended line voltage connection.
R
rgordonSep 13, 2025
What to do if the motor does not restart right away after power cycling and the LED is blinking on my Hayward XE Water Pump?
- M
  Mark BowmanSep 13, 2025
  To resolve the issue of the motor not restarting immediately after power cycling with a blinking LED on your Hayward Water Pump, ensure the LED turns off completely by waiting at least 30 seconds before reapplying power to the pump.