Healthrider HMTL07508.0 User Manual (English)

Questions and Answers:

R
Robert RoweAug 9, 2025
How to fix Healthrider HMTL07508.0 if the power does not turn on?
- S
  seansmithAug 10, 2025
  If your Healthrider Treadmill isn't turning on, here's what you can do: 1. Ensure the power cord is properly plugged into a surge suppressor, and the surge suppressor is connected to a grounded outlet. Use a surge suppressor meeting specific requirements. 2. Verify the key is fully inserted into the console after plugging in the power cord. 3. Check the reset/off circuit breaker on the treadmill frame near the power cord. If the switch is protruding, the breaker has tripped. Reset it by waiting five minutes, then press the switch to the reset position.
M
Ms. Lindsay White PhDAug 14, 2025
How to center a Healthrider Treadmill walking belt that is off-center or slips?
- D
  Dawn WyattAug 14, 2025
  Here's how to adjust your Healthrider Treadmill walking belt: * If the belt is off-center, unplug the treadmill. For a belt shifted left, turn the left idler roller bolt clockwise 1/2 turn. If shifted right, turn it counterclockwise 1/2 turn. Plug the treadmill back in and run it to check. Repeat adjustments as needed, being careful not to overtighten the belt. * If the belt slips, unplug the treadmill. Tighten both idler roller bolts clockwise 1/4 turn. The belt should allow you to lift each edge 3-4 inches off the platform when properly tightened. Plug the treadmill back in, walk on it carefully, and repeat until the slipping stops.
S
Samuel PerezAug 19, 2025
How to recalibrate Healthrider HMTL07508.0 incline if it does not change correctly?
- F
  fharrisSep 12, 2025
  To recalibrate the incline on your Healthrider Treadmill: With the key in the console, press an Incline button. While it's moving, remove the key, wait a few seconds, and re-insert it. The treadmill will rise to the maximum incline, then return to the minimum, recalibrating the system.
H
Hailey BestAug 25, 2025
What to do if Healthrider HMTL07508.0 Treadmill turns off during use?
- G
  Gary RichmondAug 25, 2025
  If your Healthrider Treadmill shuts off during use, try these steps: 1. Check the reset/off circuit breaker. If tripped, wait five minutes before resetting it. 2. Ensure the power cord is securely plugged in. If plugged in, unplug it, wait five minutes, then plug it back in. 3. Remove and re-insert the key from the console. 4. If the treadmill still won't run, no answer.
A
Aaron FrostAug 30, 2025
Why does my Healthrider HMTL07508.0 Treadmill walking belt slow down when I walk on it?
- D
  Douglas HuertaAug 30, 2025
  If the walking belt on your Healthrider Treadmill slows down when you walk on it: 1. Ensure you are using a single-outlet surge suppressor that meets the necessary specifications. 2. If the belt is too tight, unplug the treadmill. Loosen both idler roller bolts counterclockwise 1/4 turn. You should be able to lift each edge of the belt 3-4 inches off the platform when it's correctly tightened. Keep the belt centered, plug the treadmill back in, and run it for a few minutes. Repeat until properly tightened. 3. If the walking belt still slows when walked on, no answer.
L
Lawrence LinSep 3, 2025
What to do if Healthrider HMTL07508.0 Treadmill console displays remain lit after removing the key?
- S
  Sabrina RiosSep 4, 2025
  If the console displays on your Healthrider Treadmill stay lit after removing the key, the demo mode is likely activated. To deactivate it, press and hold the Stop button for a few seconds. If the displays remain lit, see THE INFORMATION MODE on page 22 to turn off the demo mode.