Heath Zenith SL-5412 User Manual

OPERATION
© 2003 DESA Specialty Products™ 595-5767-02
* resets to Auto Mode at dawn.
MANUAL MODE
ON-TIME
10 5 1 TEST
10 5 1 TEST
ON-TIME
TEST
... back on.
AUTO
1 Second OFF
then...
Move ON-TIME Switch to
1, 5 or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
Requirements
• The Light Control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a qualified
electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Model SL-5412
Light Control
Sensor
Cover
Plate
Lamp Holders
2 Wire
Connectors
6 Screws
(3 sizes included)
Gasket
2 Shells
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
Motion Sensor Light
Control for Canadian
Tire
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the
calibration time the control will be in the AUTO mode.
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
Mounting Bolt
Mounting Strap
Plastic Hanger
Rubber Plug
This package includes:
Mode: On-Time: Works: Day Night
Test 5 Sec x x
Auto 1, 5, 10 min. x
Manual Until Dawn* x
Put the ON-TIME switch on the bottom
of the sensor in the TEST position.
Put the ON-TIME switch in the 1, 5
or 10 minute position.
Manual mode only works at night be-
cause daylight returns the sensor to
AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the ON-
TIME switch in the 1, 5, or 10 position.

Heath Zenith SL-5412 Specifications

General

Power Source	Hardwired
Finish	White
Light Source	LED
Detection Range	Up to 70 feet
Number of Bulbs	2
Motion Detection Range	Up to 70 feet
Voltage	120V
Light Sensor Range	Adjustable
Motion Sensor Range	Up to 70 feet
Adjustable Head	Yes
Material	Plastic
Color	White
Bulb Type	LED
Weather Resistance	Weather resistant
Warranty	5 years

Summary

OPERATION

TEST Mode

Activates the sensor for initial setup and motion detection verification.

AUTO Mode

Enables automatic operation based on ambient light and detected motion.

MANUAL MODE

Allows manual control of lighting via a wall switch, overriding automatic functions.

INSTALLATION

Eave Mount Sensor Head Adjustment

Instructions for rotating the sensor head for proper operation in eave installations.

Mounting the Light Control

Steps for attaching the control unit, decorative shells, and rubber plug.

Wiring the Light Control

Procedure for connecting wires, securing the fixture, and positioning lamps.

TEST AND ADJUSTMENT

Initial Test Procedure

Steps to turn on power, set controls, and verify initial sensor warm-up.

Sensor Aiming and Coverage

Guidance on positioning the sensor for optimal detection range and angle.

Range and Time Delay Adjustment

Instructions for setting the detection range and duration the lights stay on.

TROUBLESHOOTING GUIDE

Lights Will Not Come On

Identifies potential causes and solutions when the light fails to activate.

Lights Stay On Continuously

Diagnoses issues causing the light to remain on without detected motion.

Lights Come On In Daylight

Troubleshoots instances where the control activates during daylight hours.

Lights Flash On and Off

Addresses intermittent light activation or flickering issues.

Lights Come On For No Apparent Reason

Resolves problems related to false triggering from environmental factors or settings.