To Next PageTo Next Page
Need help?Do you have a question about the Heatilator GNDC33 and is the answer not in the manual?
General| Type | Gas Fireplace |
|---|---|
| Fuel Type | Natural Gas or Propane |
| Heat Output | 33, 000 BTU |
| Vent Type | Direct Vent |
| Ignition Type | Electronic Ignition |
| Log Material | Ceramic Fiber |
General safety precautions and emergency procedures for gas appliances.
Identifies the NOVUS Series, Top/Rear Direct Vent Gas Appliances.
Important safety guidelines to follow before and during installation.
Details appliance certification by ANSI and UL for North American standards.
Emphasizes adherence to local building codes and national standards.
Lists necessary tools and building supplies for installation.
Explains the coding system for different NOVUS Series appliance models.
Lists and describes various vent pipes, elbows, and termination components.
Illustrates common horizontal vent configurations for top and rear venting.
Illustrates common vertical vent configurations for top and rear venting.
Provides dimensional data for rear vent NOVUS Series appliances.
Provides dimensional data for top vent NOVUS Series appliances.
Advises on safe placement away from traffic and flammable items.
Details various ways the appliance can be located in a room.
Specifies required clearances around the appliance for safety.
Shows typical framing for the appliance with combustible materials.
Provides guidelines for mantel projection and height relative to the appliance.
Warns against installing against vapor barriers or exposed insulation.
Instructions on placing and leveling the appliance on a flat surface.
Specifies clearances for horizontal vent termination components.
Details the maximum horizontal run without using elbows.
Guidelines for using 45° elbows in horizontal venting configurations.
Warns against future obstructions for horizontal terminations.
Shows venting configurations using two elbows for horizontal termination.
Shows venting configurations using three elbows for horizontal termination.
Specifies clearances for top vent termination components.
Provides guidelines for vent lengths with one elbow in top venting.
Provides guidelines for vent lengths with two elbows in top venting.
Provides guidelines for vent lengths with three elbows in top venting.
Warns against packing air spaces with insulation around the chimney.
Details various clearances required for termination cap placement.
Illustrates clearances around termination caps for different scenarios.
Prohibits termination in screened porches in the U.S. and Canada.
Specifies clearances for vertical vent sections in rear venting.
Details maximum vent lengths for rear vent vertical configurations.
Notes the need for vent supports for horizontal runs in vertical venting.
Specifies clearances for vertical vent sections in top venting.
Details maximum vent lengths for top vent vertical configurations.
Warns against packing air spaces with insulation around the chimney.
Instructions for installing the interior wall shield for vent penetration.
Shows required exterior wall hole sizes for top and rear vents.
Illustrates how vent sections pass through walls.
Advises installing a vinyl soffit shield if a cap is near vinyl soffit.
Instructions for installing the rear vent heat shield.
Details how to install firestop spacers when penetrating ceilings or floors.
Covers installation of chases and termination points.
Shows required chimney heights based on roof pitch for vertical termination.
Steps for attaching the first vent section to the appliance collars.
Instructions for connecting standard vent pipe sections together.
How to cut and assemble MI vent sections.
Steps for assembling and securing slip-type vent sections.
Guidance for installing the appliance at high altitudes.
Details on connecting the gas supply line to the appliance.
Information on gas pressure and available fuel types (natural/propane).
Specifies wiring standards for wall switches and thermostat connections.
Wiring and operational information for standing pilot ignition systems.
Lists input rates and orifice sizes for different gas types.
Wiring and operation for the intermittent pilot ignition system.
Instructions for wiring and installing the junction box.
Information on combustible, noncombustible, and sealant materials for finishing.
Warns against covering appliance grilles, which can cause fire hazards.
Instructions for attaching the hood and removing panels.
Instructions for placing logs, lava rock, vermiculite, and rock wool.
Details on glass and screen replacement and handling.
Warning about the risk of carbon monoxide with improper operation.
How to identify if the appliance has standing or intermittent pilot ignition.
Step-by-step instructions for lighting the intermittent pilot ignition.
Safety warnings and procedures for turning off gas.
Step-by-step instructions for lighting the standing pilot ignition.
Safety warnings and procedures for turning off gas.
Essential checks a qualified technician should perform before operation.
Procedures for standing and intermittent pilot operation and shutdown.
Details on converting between natural gas and propane fuels.
Explains causes and solutions for condensation and blue flames on glass.
Addresses initial odors and film formation on the glass during start-up.
Warns against using flammable liquids near the appliance.
Guide for cleaning the burner and control compartment for optimal performance.
How to check and interpret flame patterns for correct operation.
Recommends inspecting the venting system for obstructions annually.
Procedures for safely cleaning the appliance's glass.
Steps for removing and reinstalling the log set.
Describes optional components for controlling blower speed and operation.
Lists optional remote controls and multi-function wall switches.
Details available fan kits for the appliance.
Optional door styles including arched and fixed glass types.
Optional bay doors and ceramic glass panel options.
Various trim kits available for different appliance sizes and styles.
Options for cabinet trim and tile surrounds for a finished look.
Kits for converting standing pilot appliances between gas types.
Kits for converting intermittent pilot appliances between gas types.
Lists part numbers for hood and upper/lower grille replacements.
Lists part numbers for glass assemblies and log/grate sets.
Specific part number for the quick access latch.
Outlines the terms of the limited lifetime and one-year warranties.
Details conditions, exclusions, and limitations of the warranties.
Instructions on how to contact HHT for warranty service.
