What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-83-J?
If your Henny Penny Fryer displays error code “E-83-J”, it indicates that the Bulk JIB FILL switch is on when the pressure is too high. Check the JIB fill valves.
What to do if my Henny Penny EVOLUTION ELITE EEG-243 Fryer filter motor will not run?
If the filter motor on your Henny Penny Fryer won’t run, the thermal reset button on the rear of the pump motor may be tripped. First, turn the unit’s power switch to the OFF position to prevent burns from splashing shortening. Allow the motor to cool down. Then, using a screwdriver, press hard against the button until you hear a click.
What to do if my Henny Penny EVOLUTION ELITE EEG-243 is under-filled?
If the vat in your Henny Penny Fryer is under-filled, it could be due to several reasons: - The JIB might be low or empty, so you should fill the JIB. - The JIB oil line might be clogged or collapsed, so check the JIB line. - The filter pan might need cleaning, so clean the filter pan and change the paper or pad.
What to do if Henny Penny Fryer power switch is ON but the fryer is completely inoperative?
If your Henny Penny Fryer's power switch is ON but the fryer isn't working, it could be due to an open circuit. First, ensure the fryer is properly plugged in. If it is, check the breaker or fuse at the supply box.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error code E-10?
If your Henny Penny Fryer displays the error code “E-10”, it indicates a high limit issue. Allow the unit to cool down for about 15-20 minutes. Then, push up on the metal reset button located under the right side of the controls. If the high limit still doesn’t reset, the high limit component needs to be replaced.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-82-D?
If your Henny Penny Fryer displays error code “E-82–D”, it means the selector valve has failed, indicating no activity is detected. Check the motor encoder, selector valve motor, and AIF board.
What to do if Henny Penny EVOLUTION ELITE EEG-243 displays error E-60?
If your Henny Penny Fryer displays error code “E-60”, it means the AIF PC board is not communicating with the PC board. Turn the power switch to off, wait 15 seconds, and then turn it back on. If the error persists, have the connector between the PC boards checked. If necessary, replace the AIF PC board or the control PC board.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-70C?
If your Henny Penny Fryer displays error code “E-70C”, it indicates that the drain valve jumper wire is missing or disconnected. Have the jumper wire checked on the PC board at the drain switch interlock position.
What to do if Henny Penny EVOLUTION ELITE EEG-243 displays error E-15?
If your Henny Penny Fryer displays error code “E-15”, ensure that the drain knob is completely pushed in. If the error persists, have the drain switch checked.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-6A?
If your Henny Penny Fryer displays error code “E-6A”, it indicates that the temperature probe is open. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-6A”, the temperature probe should be checked.
General| Manufacturer | Henny Penny |
|---|---|
| Model | EVOLUTION ELITE EEG-243 |
| Type | Fryer |
| Fryer Type | Electric |
| Oil Capacity | 30 lb per well |
| Voltage | 208-240V |
| Phase | 1 or 3 |
| Temperature Range | 200°F |
To Next Page
