EasyManuals Logo

HIKVISION DS-2DE2A204IW-DE3 User Manual

HIKVISION DS-2DE2A204IW-DE3
101 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #32 background imageLoading...
Page #32 background image
-
Le click on a point on live image: the point is relocated to the center of the live image. With
no zooming in or out eect.
-
Hold and drag the mouse to a lower right
posion to frame an area on the live: the framed
area is zoomed in and relocated to the center of the live image.
-
Hold and drag the mouse to an upper le posion to frame an area on the live: the framed
area is zoomed out and relocated to the center of the live image.
3.
Click the
buon again to turn o the funcon.
4.1.14 Undervoltage Alarm
It is used to monitor the device voltage and warns you when the voltage is alarmingly low.
Note
This funcon is only supported by certain models.
When the device voltage is too low, a sign appears in the live view image. You are recommended
to
opmize the power supply, so as to avoid device failure.
The
funcon is on by default.
4.1.15 Display Target
Informaon on Live View
Go to Conguraon → Local → Live View Parameters for sengs.
Note
Related smart funcon should be congured and enabled in advance.
Display POS Informaon
POS informaon refers to the target features, such as target ID, etc. Supported POS informaon
types varies according to device models.
4.2 Set Transmission Parameters
The live view image may be displayed abnormally according to the network condions. In dierent
network environments, you can adjust the transmission parameters to solve the problem.
Steps
1.
Go to
Conguraon → Local .
2.
Set the transmission parameters as required.
Protocol
TCP
Network Speed Dome User Manual
21

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HIKVISION DS-2DE2A204IW-DE3 and is the answer not in the manual?

HIKVISION DS-2DE2A204IW-DE3 Specifications

General IconGeneral
Sensor typeCMOS
Progressive scanYes
Number of sensors1
Optical sensor size1/3 \
Maximum resolution1920 x 1080 pixels
Video compression formatsH.264, H.264+, H.265, H.265+
Analog signal format systemNTSC, PAL
Pan range0 - 330 °
Pan speed100 °/sec
White balanceATW, Auto, Manual
Tilt angle range0 - 90 °
Camera shutter speed1/1 - 1/30000 s
Minimum illumination0.005 lx
TypeIP security camera
Placement supportedIndoor & outdoor
Connectivity technologyWired
FocusMotorized/Manual
Digital zoom16 x
Optical zoom4 x
Focal length range- mm
Maximum aperture number2.7
Minimum aperture number1.6
Detection distance0.01 m
Audio input channels1 channels
Wi-Fi-
Number of users20 user(s)
Cabling technology10/100Base-T(X)
Networking standardsIEEE 802.1x
Compatible memory cardsMicroSD (TransFlash), MicroSDHC, SDXC
DC output voltage12
Power source typeDC
Power consumption (typical)12 W
Operating temperature (T-T)-20 - 60 °C
IK codeIK10
Form factorDome
Product colorBlack, White
Housing materialAcrylonitrile butadiene styrene (ABS), Aluminium, Polycarbonate (PC)
International Protection (IP) codeIP66
Weight and Dimensions IconWeight and Dimensions
Width130.7 mm
Height101.7 mm
Weight (with stand)530 g

Related product manuals