HIKVISION DS-PDPG12P-EG2-WB - Page 6

7
Specificaon
6
Operaon Cauon and Device Maintenance
- All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire prevenon
regulaons and other related regulaons in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon.
Avoid the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment
damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then
please contact the service center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon.
Avoid the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment
damage).
- Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operaon
temperature), cold, dusty or damp locaons, and do not expose it to high electromagnec radiaon.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden
(ignorance can cause fire danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not
a malfuncon however), and affecng the endurance of sensor at the same me.
- Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used baeries according to the instrucons provided by the baery manufactur-
er.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situaon.
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
5
Formang
Hold the tamper switch for 8 s and power the device on at the same me. The red LED flashes 3 mes when the formang
operaon is completed.
6
Model DS-PDPG12P-EG2-WB/WE
Detecon Performan
ce
Detecon Method Passive Infrared,Acousc Sensor
Detecon Range 12m
Detecon Angle 85.9°
Detecon Zones 52
Detectable Speed 0.3 to 2m/s
Pet Immunity 30Kg
PIR Sensivity Auto,High,Pet
White Light Filter 6500lux
Glass Type
Float,Plate,Tampered,Wired,Laminated
Leaded,Double Glazing
Glass Break Range 8m
Glass Thickness 2.4mm to 6.4mm
Glass Break Sensivity 2m,4m,6m,8m
Digital Temperature Compensaon Support
Glass Size 0.3m x 0.3m to 3m x 3m
Creep Zone Protecon Support
Feature
Digital Processing Support
Sealed Opcs Support
Tamper Protecon Front,Rear
Environment Temperature Indicator Support
Signal Strength Indicator Support
Interface
Power Switch Power Up Enrolling
LED Indicator Green(PIR),Red(BG),Blue(alarm)
Transmission
Transmission Technology
Tri-X Wireless
Transmission Method Two-Way RF Wireless
Transmission Frequency 433MHz/868MHz
Transmission Security AES-128 Encrypon
Transmission Range(Free Space) 1Km(433MHz )/1.6 Km(868MHz)
Frequency Hopping Support
Enrolling Method Power up,Remote ID,QR Code
Electrical Characteris
cs
Power Supply Baery Powered
Baery Type CR123A × 2
Typical Voltage 3V
Standard Baery Life 4 Years