Hiland F-1108-FPT - User Manual

Questions and Answers

R
Ryan MorganSep 15, 2025
Why is the Hiland F-1108-FPT Patio Heater burner flame is low?
- V
  Victor BellSep 15, 2025
  A low burner flame on your Hiland Patio Heater can be due to several reasons. Low gas pressure is a common cause; turn the cylinder valve OFF and replace the cylinder. If the outdoor temperature is below 40ºF and the tank is less than 1/4 full, use a full cylinder. Also, inspect the burner and orifices for any blockages.
A
Alexandra DunnAug 25, 2025
What to do if my Hiland Patio Heater pilot won’t light?
- M
  Mary LopezAug 25, 2025
  If the pilot light on your Hiland Patio Heater won't ignite, it could be due to a few reasons. There might be air in the gas line; open the gas line and bleed it (pressing control knob in) for no more than 1 - 2 minutes or until you smell gas. If the gas pressure is low with the cylinder valve fully open, turn the cylinder valve OFF and replace the cylinder. You can also try using a match to light the pilot, and consider obtaining a new igniter.
A
Anna MclaughlinAug 25, 2025
What to do if my Hiland F-1108-FPT Patio Heater burner won’t light?
- K
  Kathryn AllenAug 26, 2025
  If the burner won't light, it could be due to several reasons. First, the propane cylinder might be frosted over; wait until it warms up. Second, there might be a blockage in the orifice; clear any blockage. Third, the control knob might not be in the ON position; turn it to ON.
K
Kathleen LongAug 26, 2025
What to do if the pilot won’t stay lit on my Hiland Patio Heater?
- P
  pmillerAug 27, 2025
  If the pilot light won't stay lit, the issue could be due to: * Dirt built up around the pilot: Clean the dirt from around the pilot. * A loose connection between the gas valve and pilot assembly: Tighten the connection and perform a leak check. * A faulty thermocouple: Replace the thermocouple.
P
Philip CastroSep 16, 2025
How to stop carbon build-up and thick black smoke from Hiland F-1108-FPT?
- T
  Terri RobertsSep 16, 2025
  If you're seeing carbon build-up or thick black smoke from your Hiland Patio Heater, it's likely due to dirt or film on the reflector and burner screen, so clean them. Another cause could be a blockage in the burner; remove any blockage and clean the burner inside and outside.
J
Jodi HoSep 23, 2025
How to fix carbon build-up and black smoke in Hiland Outdoor Fireplace?
- B
  Brenda HowardSep 23, 2025
  Carbon build-up and thick black smoke in your Hiland Outdoor Fireplace may be caused by: * Dirt or film on the burner: Clean the burner. * A blockage in the burner: Remove any blockage and thoroughly clean the burner, both inside and out.
M
Michele SmithSep 8, 2025
What to do if the igniter fails on my Hiland F-1108-FPT Patio Heater?
- S
  Sharon NewmanSep 8, 2025
  If the igniter fails, use a match to light the pilot. Obtain a new igniter and replace the old one.
E
ericajonesSep 9, 2025
What to do if there is low gas pressure with a fully open cylinder valve on my Hiland F-1108-FPT Patio Heater?
- K
  kennethwaltersSep 9, 2025
  If you have low gas pressure even with the cylinder valve fully open, turn the cylinder valve OFF and replace the cylinder.
K
Krystal TaylorSep 2, 2025
What to do if my Hiland Patio Heater burner won't light?
- D
  danielsstephanieSep 3, 2025
  If the burner on your Hiland Patio Heater isn't lighting, there are a few things to check. First, if the propane cylinder is frosted over, wait for it to warm up. Also, check for any blockages in the orifice and clear them. Finally, make sure the control knob is turned to the ON position.
S
Sarah PerezAug 31, 2025
Why won't the burner light on my Hiland F-1108-FPT Patio Heater?
- D
  Daniel MorganSep 1, 2025
  If the burner on your Hiland Patio Heater won't light, it could be due to a frosted propane cylinder; wait until the propane cylinder warms up and becomes unfrosted. Also, check for any blockage and clear it. Ensure that the control knob is turned to the ON position.

This document describes the Hiland Premium Series Outdoor Fire Pit Table, Model # F-1108-FPT, a gas-fired outdoor infrared patio heater designed for residential use. The manual provides comprehensive instructions for assembly, operation, and maintenance, emphasizing safety precautions throughout.

Function Description

The Hiland Outdoor Fire Pit Table serves as an outdoor heating appliance, utilizing propane gas to produce a flame for warmth and ambiance. It is designed to be used exclusively outdoors, providing a decorative and functional centerpiece for patios or other open-air spaces. The unit is equipped with a burner that produces a flame, and the heat output can be adjusted. A removable burner cover allows the fire pit to be covered when not in use, protecting the burner and glass beads. The design incorporates a housing for a standard 20 lb. propane cylinder, which fuels the appliance.

Usage Features

The fire pit table is designed for ease of use with several key operational features:

Propane Fuel System: It operates on a standard 20 lb. propane cylinder (sold separately) with a vapor withdrawal supply system. The cylinder connects to the fire pit via a hose and regulator assembly, which is supplied with the appliance.
Ignition System: The unit features a gas control knob that allows users to turn the gas supply ON/OFF and adjust the flame intensity. To light the fire pit, the control knob is pushed in and turned counterclockwise to the "IGNITE" position. A clicking sound indicates the ignition process. For initial starts or after a cylinder change, the control knob should be held in for 2 minutes to purge air from the gas lines.
Adjustable Heat Output: Once lit, the flame can be adjusted from "HIGH" to "LOW" by pushing in and turning the control knob. This allows users to control the heat output according to their preference.
Safety Shut-Off: To extinguish the burner, the control knob is depressed and turned clockwise to "OFF." The propane cylinder valve should also be turned OFF when the heater is not in use.
Outdoor Use Only: The fire pit is strictly for outdoor use and must not be operated inside buildings, garages, or any other enclosed areas to prevent carbon monoxide poisoning and fire hazards. Adequate fresh air ventilation is crucial.
Clearances: Specific clearances from combustible materials are required: at least 24 inches from the sides and rear, and 6 feet from the ceiling. The fire pit should be placed on a hard and level surface, away from windows, air intake openings, sprinklers, and other water sources.
Glass Beads: The burner area is filled with glass beads, which enhance the aesthetic appeal of the flame.
Burner Cover: A removable burner cover is provided to protect the burner and glass beads when the fire pit is not in use or after use.

Maintenance Features

Regular maintenance is essential to ensure the longevity and safe operation of the fire pit table:

Exterior Cleaning: Exterior surfaces should be cleaned with warm soapy water. Flammable or corrosive cleaning agents should never be used. The manual also suggests applying a good quality car wax to the exterior surfaces every few months to protect the finish, especially flat surfaces, from humidity and moisture. This is particularly important for powder-coated surfaces, which are sensitive to these elements.
Burner Area Maintenance: The area around the burner must be kept dry at all times. The control valve assembly should never be submerged in water; if it is, it must be replaced.
Airflow and Ventilation: It is imperative to keep the control compartment, burners, and circulating air passageways clean and free from obstructions. The ventilation opening(s) of the cylinder enclosure must also be kept clear from debris. Signs of possible blockage include gas odor with extreme yellow tipping of flame, the fire pit not reaching the desired temperature, excessively uneven glow, or popping noises.
Burner Cleaning: Spiders and insects can nest in burner orifices, creating a dangerous condition. Burner holes should be cleaned using a heavy-duty pipe cleaner, and compressed air can help clear smaller particles. Carbon deposits, if they develop, should be cleaned with warm soapy water to prevent fire hazards.
Hose Assembly Inspection: The hose assembly should be inspected before each use for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. If the hose leaks, it must be replaced with a manufacturer-specified replacement.
Burner Inspection: The burner itself should be inspected before use. If it is damaged, it must be replaced with a manufacturer-specified replacement before the appliance is put into operation.
Annual Inspection: The fire pit should be inspected at least annually by a qualified service person. More frequent cleaning may be required as necessary.
Leak Testing: A leak test must be performed outdoors before initial use, after any gas connections are loosened or removed, and whenever a new propane cylinder is connected. This involves applying a soapy water solution to connections and checking for bubbles.
Storage: When not in use, the control knob should be turned OFF, and the LP source disconnected. The fire pit should be stored upright in a well-ventilated area, sheltered from direct contact with inclement weather. If storing indoors, the propane cylinder must be disconnected and stored outdoors, out of reach of children, and in a well-ventilated area. The cylinder should never be exposed to direct sunlight or excessive heat. A dust cap should be placed on the cylinder valve outlet when not in use.
Service: Only a qualified service person should repair gas passages and associated components. The fire pit must be allowed to cool completely before attempting any service.

Hiland F-1108-FPT Specifications

General

Brand	Hiland
Model	F-1108-FPT
Fuel Type	Propane
Material	Steel
Wheels	Yes
Color	Hammered Bronze
Type	Patio Heater
Tank Capacity	20 lb propane tank
Ignition Type	Piezo ignition
Height	87 inches