Hilti DST 20-CA Manual

Hilti DST 20-CA

48 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

DST 20CA

English

Printed: 07.06.2017 | Doc-Nr: PUB / 5355799 / 000 / 00

Table of Contents

Other manuals for Hilti DST 20-CA

Original Operating Instructions52 pages

Questions and Answers:

V
vjonesAug 16, 2025
What to do if Hilti DST 20-CA Saw blade is jammed in the kerf and the saw doesn’t start?
- J
  Jeremy MilesAug 16, 2025
  If your Hilti Saw blade is jammed in the kerf and the saw won’t start, it could be due to these reasons: * A piece of steel cut free is jammed in the kerf: Carefully try to free the saw blade by moving the saw head forward and back alternately. Once the blade moves freely, attempt to start the blade drive. Use caution to avoid excessive force that could cause damage. If the saw blade remains stuck, disconnect it from the saw and use a breaker/jackhammer to carefully chisel away concrete until the blade is free. * The part cut free is pressing against the saw blade: Disconnect the saw blade from the saw. Remove the part that has been cut free.
E
Ernest WillisAug 18, 2025
What to do if the saw blade slips on a Hilti Saw?
- J
  Julie MorrisAug 18, 2025
  If the saw blade slips on your Hilti Saw, consider these potential causes and solutions: * Insufficient tightening torque: Grease the thread of the clamping screw and tighten it to the specified torque. * Contaminated clamping surfaces: Clean and degrease the clamping surfaces of the flange and saw blade. * Damaged threads: Clean and inspect the threads of the clamping screw and inner flange. Replace if necessary. * Stiff clamping screw thread: Grease the thread of the clamping screw.
W
William CortezAug 21, 2025
Why does my Hilti DST 20-CA have low sawing performance?
- C
  Caroline SanchezAug 22, 2025
  Low sawing performance with your Hilti Saw can stem from a few reasons. First, ensure the saw blade specification is correct for the material you're cutting; if it's unsuitable, change to the right specification. Second, check the depth of cut; an excessive depth can hinder performance, so reduce it. Finally, the saw advance speed might be too low; try increasing it to improve performance.
E
elewisAug 28, 2025
How to fix a Hilti DST 20-CA when the cut is not straight?
- D
  Douglas LynchAug 28, 2025
  If your Hilti Saw isn't cutting straight, several factors could be the cause: * Inadequate blade tension or a blunt saw blade: Change the saw blade, paying attention to the specification. * Improper guide cut: Ensure you're adhering to the recommended guide values. * Flange issues: Check the flange is seated correctly and the securing screw's tightening torque is correct. Repeat the flange installation procedure if needed. * Guide roller play: Inspect the rollers and adjust them. If adjustment isn't enough, replace the rollers or guide rail. * Loose rail fastenings: Check and refasten the rails. * Rail distortion: Install additional rail supports.
B
Beverly RussellAug 31, 2025
Why is the Hilti DST 20-CA performance so low?
- E
  Edward ThomasAug 31, 2025
  Low sawing performance on your Hilti Saw can stem from several reasons: * Incorrect blade: Ensure the saw blade specification is correct for the material you're cutting. Change to the right specification if needed. * Excessive cutting depth: Reduce the depth of cut. * Slow advance speed: Increase the saw advance speed. * Blade wandering: Refer to the troubleshooting steps for a cut that isn't straight. * High reinforcement content: If possible, reposition the cut to avoid areas with high reinforcement. * Incorrect blade speed: Set the speed of rotation correctly.
M
mcrawfordSep 3, 2025
Why is my Hilti DST 20-CA's sawing performance low?
- D
  Danielle PowellSep 3, 2025
  There are several reasons for low sawing performance: * The saw blade specification might be unsuitable, so check and change to the correct one. * The depth of cut may be excessive, so reduce it. * The saw advance speed might be too low, so increase it. * A drop in performance can be caused by the blade wandering off course. See the troubleshooting section regarding cuts that are not straight. * A drop in performance may be caused by high reinforcement content. If so, make the cut in a different position. * The saw blade speed of rotation might be too high or too low, so set the speed of rotation correctly.
C
christopher58Sep 5, 2025
How to fix a Hilti Saw cut that is not straight?
- C
  Christine TaylorSep 5, 2025
  A cut that is not straight can be caused by several factors: * Inadequate blade tension. Change the saw blade. * A blunt saw blade. Change the saw blade, paying attention to the specification. * An inaccurate guide cut, or failure to make one at all. Check whether the given guide values were adhered to. * Excessive play at the guide rollers. Check the play at the rollers and adjust them correctly. If adjustment isn't enough, replace the rollers or the guide rail. * Loose rail fastenings. Check the fastenings and refasten the rails. * Rail distortion (twisting). Install additional rail supports.
V
Vernon ReynoldsSep 9, 2025
What to do if the Hilti DST 20-CA Saw blade is jammed in the kerf and the saw doesn’t start?
- A
  Andrea HernandezSep 9, 2025
  If the saw blade is jammed, it could be due to: * A piece of steel cut free jammed in the kerf. Try to lift the saw blade out of the kerf by alternately moving the saw head forward and back (advance / return). Try to start the blade drive as soon as the blade can be moved freely. Avoid using excessive force, as this could cause damage. If the saw blade can’t be moved: Disconnect the saw blade from the saw and use a breaker / jackhammer to chisel away concrete until the blade is free. * The part cut free pressing against the saw blade. Disconnect the saw blade from the saw. Remove the part that has been cut free.
J
jacob21Sep 12, 2025
Why is there stiff movement of the fastening bolts on the Hilti DST 20-CA Saw arm?
- T
  Tasha GriffinSep 12, 2025
  Stiff movement of the fastening bolts on the saw arm can occur if the thread or the contact surfaces of the flange are dirty. Clean thoroughly, removing any dirt adhering to parts.

Hilti DST 20-CA Specifications

General

Brand	Hilti
Model	DST 20-CA
Category	Saw
Language	English

Related product manuals

Preview: Hilti DS WS15

Preview: Hilti DSH 700

Preview: Hilti DSH 600

Preview: Hilti DSH 700X

Preview: Hilti DSH 900-X

Hilti DSH 900-X

Preview: Hilti DSH 600-X

Hilti DSH 600-X

Preview: Hilti DSH 700-X

Hilti DSH 700-X

Preview: Hilti DSW 1510-CA

Hilti DSW 1510-CA

Preview: Hilti DSF 1030-TS

Hilti DSF 1030-TS

Preview: Hilti Nuron DSH 600-22

Hilti Nuron DSH 600-22

Preview: Hilti D-LP 30