Why the orbital action doesn't work on my Hilti SJT 6-A22 Power Tool?
If the orbital action isn’t working, it could be due to foreign matter clogging the orbital-action mechanism or the adjusting lever being in the “0” position. Check for foreign matter in the area of the orbital-action fork and clean it out. If that doesn't resolve the issue, adjust the orbital-action adjusting lever to the desired setting.
What to do if all 4 LEDs blink and the Hilti SJT 6-A22 Power Tool doesn’t run?
If all 4 LEDs blink and the power tool doesn’t run, it indicates that the tool has been overloaded. Release the on/off switch and then press it again. Allow the power tool to run under no load for approximately 30 seconds.
Why does my Hilti SJT 6-A22 Power Tool battery run down more quickly than usual?
If the battery runs down more quickly than usual, it could be due to a very low ambient temperature. Let the battery warm up slowly to room temperature.
What to do if 1 LED blinks and the Hilti Power Tool doesn’t run?
If 1 LED blinks and the power tool doesn’t run, it could be due to: * Low battery: Change the battery and charge the empty battery. * The battery is too hot or too cold: Allow the battery to cool down or warm up slowly to room temperature.
What to do if the Hilti SJT 6-A22 or battery gets very hot?
If the power tool or battery gets very hot, it may be due to an electrical fault. Immediately switch the power tool off, remove the battery, keep it under observation, and allow it to cool down.
How to fix the Hilti SJT 6-A22 saw blade that drops out?
If the saw blade drops out, it could be due to: * The saw blade is not correctly engaged: Repeat the insertion procedure, ensuring the blade holder is fully open and the saw blade is pushed all the way in against the spring resistance. * The clamping system is clogged with foreign matter: Clean out the blade holder.
Why doesn’t the Hilti SJT 6-A22 battery engage with an audible click?
If the battery doesn’t engage with an audible click, the retaining lugs on the battery may be dirty. Clean the retaining lugs and refit the battery.
What to do if the Hilti Power Tool saw blade cannot be inserted?
If the saw blade cannot be inserted, the clamping system may be clogged with foreign matter. Clean out the blade holder.
What to do if the orbital action doesn’t work on my Hilti SJT 6-A22?
If the orbital action doesn’t work, consider the following: * The orbital-action mechanism is clogged with foreign matter: Check whether foreign matter is present in the area of the orbital-action fork and clean it out. * The orbital-action adjusting lever is in position “0”: Adjust it to the desired setting.
How to fix the orbital action if it cannot be adjusted on Hilti SJT 6-A22?
If the orbital action cannot be adjusted, it may be due to foreign matter in the orbital-action adjusting lever groove. Clean out the orbital-action adjusting lever groove.
General safety warnings and instructions for operating power tools safely and effectively.
Specific safety advice for operating jig saws, including handling and workpiece securing.
Further safety guidelines covering personal, electrical, and specific jig saw operational safety.
Instructions for safe handling, storage, and use of lithium-ion batteries.
Defines the product's intended applications and lists prohibited uses.
Safety precautions and preparation steps before operating the power tool.
Steps for safely switching the power tool on and off.
General| Tool Type | Reciprocating saw |
|---|---|
| Battery Voltage | 21.6 V |
| Stroke Length | 28 mm |
| A-weighted Emission Sound Pressure Level | 88 dB(A) |
| Uncertainty for Declared Vibration Emission Value (K) | 1.5 m/s² |
| Uncertainty for Declared Sound Power Level (K) | 3 dB(A) |
| Weight | 2.9 kg |
| Cutting Depth in Metal | 10 mm |
| Base Material | Metal |
| Stroke Rate | 0 - 3000 strokes/min |
To Next Page
