What to do if Hilti Power Tool doesn’t start and the service indicator lights red?
If your Hilti Power Tool doesn’t start and the service indicator is red, it could be due to worn-out carbon brushes. Have the power tool checked by a trained electrical specialist and the carbon brushes replaced if necessary. It also could be caused by a faulty tool, in that case the product should be repaired only by Hilti Service.
How to release a chisel stuck in a Hilti TE 500 chuck?
If the chisel cannot be released from the chuck, ensure that the chuck is pulled back fully. Pull the chuck back as far as it will go and remove the insert tool.
How to troubleshoot a Hilti TE 500 that doesn't start?
If your Hilti Power Tool isn't starting, here's what to check: * First, ensure there isn't an interruption in the electric supply by testing another appliance in the same outlet. * Second, examine the supply cord and plug for any defects. If found, have them checked and replaced by a trained electrical specialist. * Third, if using a generator, verify it's not in sleep mode by applying a load with another power consumer. * Fourth, in case of an electrical fault, have the power tool and supply cables inspected by a trained specialist. * Finally, if the electronic restart interlock is activated, switch the power tool off and then on again.
Why doesn't my Hilti TE 500 Power Tool achieve full power?
If your Hilti Power Tool isn't reaching full power, consider these potential causes: * The gauge (cross section) of the extension cord conductors may be inadequate. Use an extension cord with an adequate conductor cross section. * The control switch may not be fully pressed. Ensure you press the control switch as far as it will go.
Why is there no hammering action in my Hilti TE 500?
If there is no hammering action, the tool may be faulty or servicing is due. Have the product repaired only by Hilti Service.
Explains the meaning of danger, warning, caution, and note symbols used in the manual.
Details warning and obligation signs with their meanings.
Outlines the intended applications, working environment, and limitations for the power tool.
Covers the chuck system, control switches, and vibration-absorbing grips.
Explains the electronic restart interlock and the AVR active vibration reduction system.
Details optional theft protection, LED indicators, and extension cord usage.
Specific instructions for outdoor extension cords and powering with generators or transformers.
Lists available accessories and consumables, including insert tools.
Presents detailed technical specifications including voltage, current, weight, and dimensions.
Covers general safety for work area, electrical safety, and personal safety.
Safety guidelines for work area, electrical safety, plug integrity, and cord care.
Measures for staying alert, using safety equipment, and avoiding accidental starting.
Guidelines for proper use, maintenance, handling, and professional servicing of the power tool.
Provides further safety advice including noise protection, grip care, and cord management.
Focuses on safe work areas, ventilation, and specifies required personal protective equipment.
Step-by-step instructions for attaching and positioning the side handle.
Instructions for unlocking the tool (theft protection) and using extension cords/generators.
Steps for preparing the tool, fitting, and removing insert tools.
Details chiseling operation, adjustment, and control switch functions.
Explains unlocking and activation of the optional TPS theft protection system.
Guidance on cleaning and protecting insert tools and the power tool's exterior.
Explains the service indicator and general maintenance checks required.
Lists common faults, their possible causes, and suggested remedies for the tool.
Continues listing power tool faults, their causes, and remedies.
Details the terms and conditions of the Hilti manufacturer's warranty.
General| Chuck type | SDS Max |
|---|---|
| Product color | Black, Red |
| Country of origin | Germany |
| Impact energy (max) | 7.5 J |
| Sound pressure level | 94 dB |
| Chiseling performance | 900 cm³/min |
| Idle impact rate (max) | 3180 IPM |
| Vibration level (chiseling) | 12.1 m/s² |
| Input power | 1100 W |
| Power source | AC |
| Power plug type | Type C |
| Quantity per shipping (inner) case | 1 pc(s) |
Weight and Dimensions| Depth | 471 mm |
|---|---|
| Width | 108 mm |
| Height | 243 mm |
| Weight | 5600 g |
| Package depth | 100 mm |
| Package width | 150 mm |
| Package height | 76 mm |
| Package weight | 500 g |
To Next Page
