What to do if the chisel cannot be released from the chuck of Hilti TE 500-AVR?
If the chisel cannot be released from the chuck of your Hilti Power Tool, make sure that you pull the chuck back as far as it will go and then remove the insert tool.
Why is the service indicator light on my Hilti Power Tool?
If the service indicator light is on, it could mean the carbon brushes are worn and need to be checked and replaced by a trained electrical specialist. Alternatively, the Hilti Power Tool may be faulty or due for servicing, in which case it should be repaired only by Hilti Service.
What to do if my Hilti TE 500-AVR breaker doesn’t start?
If your Hilti Power Tool breaker doesn’t start, there might be an interruption in the electric supply. Try plugging in another electric tool or appliance to check if it works. It's also possible that the electronic restart interlock is activated, so try switching the power tool off and then on again. Another cause might be that the generator is in sleep mode. To solve this, apply a load to the generator by connecting a second power consumer (e.g. worklight), then switch the tool off and on again. If none of these actions work, there may be a fault in the tool, so have the product repaired by Hilti Service, or the carbon brushes may be worn, so have them checked by a trained electrical specialist and replaced if necessary.
Why doesn't my Hilti TE 500-AVR breaker achieve full power?
If the Hilti Power Tool breaker doesn’t achieve full power, the extension cord might be too long or its gauge is inadequate. Try using an extension cord of an approved length and/or of adequate gauge. Also, make sure the control switch is fully pressed.
What does it mean when the service indicator blinks on my Hilti Power Tool?
If the service indicator is blinking on your Hilti Power Tool, it indicates a fault has occurred in the tool. You should have the product repaired by Hilti Service.
How to fix no hammering action on Hilti TE 500-AVR Power Tool?
If your Hilti Power Tool has no hammering action, it might be too cold. Bring the tip of the accessory tool into contact with the working surface, switch the power tool on, and allow it to run. Repeat if necessary until the hammering mechanism starts.
Why won't my Hilti Power Hammer start?
Several factors could prevent your Hilti Power Hammer from starting: * There may be an interruption in the electrical supply. Try plugging in another electrical tool to verify. * The electronic restart interlock may be activated. Try switching the power tool off and on again. * If you're using a generator, it might be in sleep mode. Connect another device like a work light to apply a load, then switch the tool off and on again. * There may be a fault in the tool. In this case, have the product repaired by Hilti Service. * The carbon brushes may be worn. Have them checked by a trained electrical specialist and replaced if needed.
What to do if my Hilti Power Hammer doesn't achieve full power?
If your Hilti Power Hammer isn't reaching full power, consider these potential causes: * The extension cord may be too long or of inadequate gauge. Use an extension cord of the correct length and gauge. * The control switch may not be fully pressed. Ensure you press the control switch completely.
Why is the service indicator light on my Hilti Power Hammer?
If the service indicator light is illuminated on your Hilti Power Hammer, it could indicate: * Worn carbon brushes. Have them checked and replaced by a trained electrical specialist if necessary. * A fault in the tool or that servicing is due. Have the product repaired only by Hilti Service.
What to do if my Hilti Power Hammer has no hammering action?
If your Hilti Power Hammer isn't hammering, it might be too cold. Try bringing the tip of the accessory tool into contact with the working surface, switch the power tool on and allow it to run. Repeat this procedure if necessary until the hammering mechanism starts working.
Covers essential safety instructions applicable to all power tools, focusing on electric shock, fire, and injury prevention.
Provides instructions on the correct usage, maintenance, and handling of power tools to ensure safety and operational efficiency.
Specific safety advice tailored for hammer-type tools, including hearing protection and the use of auxiliary handles.
Specifies that the breaker is designed for medium-duty chiseling work on masonry and concrete.
Explains the integrated Active Vibration Reduction (AVR) system and its benefit in reducing user exposure to vibration.
Guidelines for proper cleaning and maintenance of the breaker to ensure its safety and longevity.
A comprehensive guide to diagnosing and resolving common operational issues and faults with the breaker.
General| Power | 1100 W |
|---|---|
| Weight | 5.9 kg |
| Impact Energy | 5.2 J |
| Full Hammering Frequency | 3510 impacts/minute |
| Active Vibration Reduction | Yes |
| Weight according to EPTA Procedure 01/2003 | 5.9 kg |
| Dust Removal Module Available | Yes |
| Dust Removal | Optional |
| Power Input | 1100 W |
| Voltage | 230 V |
| Cable Length | 4 m |
| Working Mode | Chiselling |
To Next Page
