Hilti TE 700-AVR - User Manual

Other manuals for Hilti TE 700-AVR

User Manual184 pages

Operating Instructions24 pages

Manual156 pages

Questions and Answers

J
Jared WelchSep 4, 2025
Que faire si mon burineur Hilti Power Hammer ne démarre pas ?
- K
  katherinealvaradoSep 4, 2025
  Si votre burineur Hilti Power Hammer ne démarre pas, cela peut être dû à plusieurs raisons : * L'initialisation de l'électronique est en cours. Dans ce cas, arrêtez puis remettez en marche l'appareil. * Le dispositif de verrouillage anti-démarrage électronique est activé après une coupure d'alimentation électrique. Essayez d'arrêter puis de remettre en marche l'appareil. * L'alimentation réseau est coupée. Branchez un autre appareil électrique et vérifiez s'il fonctionne. * Le générateur est en mode Veille. Chargez le générateur avec un second consommateur, puis arrêtez et remettez en marche l'appareil. * L'appareil est endommagé ou l'échéance du prochain entretien est atteinte. Faites réparer le produit exclusivement par le S.A.V. Hilti.
S
shannonandersonSep 18, 2025
How to release a chisel stuck in a Hilti Power Tool?
- L
  leahcamachoSep 18, 2025
  If the chisel cannot be released from the chuck of your Hilti Power Tool, it's likely because the chuck is not pulled back fully. To release the chisel, pull the tool lock back as far as it will go and then remove the insert tool.
J
jason76Sep 16, 2025
How to fix no hammering action on a Hilti Power Tool?
- S
  Sarah HillSep 16, 2025
  If you're experiencing no hammering action with your Hilti Power Tool, it might be because the power tool is too cold. Try bringing the tip of the accessory tool into contact with the working surface, switch the power tool on, and allow it to run. If necessary, repeat the procedure until the hammering mechanism begins to work. Another potential cause is that the chuck isn't sufficiently greased. To resolve this, inject 1-2 strokes of grease from the dispenser into the chuck, using genuine Hilti grease. Then, fit the accessory tool and distribute the grease in the chuck by pulling the accessory tool in and out several times.
L
Lori AllisonSep 14, 2025
Why does my Hilti Power Tool breaker switch off while running?
- M
  Maria FarleySep 14, 2025
  If your Hilti Power Tool breaker switches itself off while running, it's likely because the overheating prevention cut-out has been activated. To fix this, allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
A
Angelica HoganSep 12, 2025
What to do if my Hilti Power Tool breaker doesn’t achieve full power?
- A
  Alexandria HoltSep 12, 2025
  If your Hilti Power Tool breaker doesn’t achieve full power, there are a few potential causes. One possibility is that power reduction is active. To resolve this, press the power level selector switch, paying attention to the power level indicator. Additionally, try unplugging the power tool from the electric supply and then plugging it back in. Another cause could be that the extension cord is either too long or not thick enough (inadequate gauge). In this case, use an extension cord of an approved length and adequate gauge. Finally, the voltage provided by the electric supply might be too low. If this is the case, try connecting the power tool to a different power source.
A
amycoffeySep 12, 2025
Why doesn't my Hilti Power Tool breaker start?
- S
  samanthaloganSep 12, 2025
  If your Hilti Power Tool breaker doesn't start, it could be due to several reasons. First, the electronics might be initializing, which can take up to 4 seconds after plugging in. In this case, try switching the power tool off and then on again. Another reason could be the electronic restart interlock being activated after an interruption in the electric supply; again, switch the tool off and on. Check for a general interruption in the electric supply by plugging in another electric tool or appliance to see if it works. If you're using a generator, it might be in sleep mode; apply a load by connecting another device like a worklight, then switch the tool off and on. If none of these steps work, the tool might be faulty and should be repaired by Hilti Service.
R
Rebecca RomeroSep 9, 2025
Que faire si mon burineur Hilti Power Hammer s'arrête en cours de fonctionnement ?
- J
  Juan WilliamsSep 9, 2025
  Si votre burineur Hilti Power Hammer s'arrête en cours de fonctionnement, la protection contre la surchauffe a peut-être été activée. Laissez refroidir l'appareil et nettoyez les ouïes d'aération. La marche à vide est encore possible.
D
David SanchezSep 7, 2025
Que signifie le clignotement en rouge de l'indicateur de maintenance sur mon Hilti Power Hammer ?
- C
  cynthia54Sep 7, 2025
  Si l'indicateur de maintenance clignote en rouge sur votre Hilti Power Hammer, cela peut indiquer que la protection contre la surchauffe a été activée. Laissez refroidir l'appareil et nettoyez les ouïes d'aération. La marche à vide est encore possible. Une autre cause possible est que la tension de la source d'alimentation électrique est trop élevée. Essayez de changer de prise et de contrôler le réseau d'alimentation.
B
Bruce WalkerSep 5, 2025
Que faire si mon Hilti Power Hammer n'a pas de percussion ?
- A
  Amber RichardsonSep 5, 2025
  Si votre Hilti Power Hammer n'a pas de percussion, tenez compte des éléments suivants : * L'appareil est peut-être trop froid. Posez le burineur sur le support et laissez-le tourner à vide. Répétez si nécessaire jusqu'à ce que le mécanisme de frappe fonctionne. * Le mandrin n'est peut-être pas suffisamment graissé. Donnez 1 à 2 coups de graisse Hilti d'origine dans le mandrin, mettez ensuite l'outil en place et tirez plusieurs fois sur l'outil afin que la graisse se répartisse bien dans le mandrin.
E
elizabeth09Aug 20, 2025
What to do if the service indicator blinks red on my Hilti Power Tool?
- D
  Daniel PierceAug 20, 2025
  If the service indicator on your Hilti Power Tool is blinking red, it could be due to a couple of reasons. One reason is that the overheating prevention cut-out has been activated. To address this, allow the tool to cool down and clean the air vents. Note that running under no load is still possible. Another reason might be that the voltage provided by the electric supply is too high. In this case, try using a different power outlet and check the electric supply.

Summary

Safety

General Power Tool Safety Warnings

Essential safety precautions for operating power tools.

Work Area and Electrical Safety

Guidelines for safe work environment and electrical connections.

Personal Safety

Advice on staying alert and using common sense during operation.

Personal Protective Equipment (PPE)

Emphasizes the importance of PPE for injury prevention.

Preventing Unintentional Starting

Instructions to avoid accidental tool activation.

Hammer and Breaker Safety

Specific safety precautions for hammer/breaker operation.

Operation

Workplace Preparations and Handle Fitting

Accessory Tool Installation

Accessory Tool Removal

Troubleshooting

Troubleshooting: Start Issues

Lists common problems and solutions for the breaker not starting.

Troubleshooting: Hammering Issues

Lists common problems and solutions for no hammering action.

Troubleshooting: Indicator and Power Issues

Addresses issues with indicators, overheating, and power reduction.

Hilti TE 700-AVR Specifications

General

Weight	7.9 kg
Single Impact Energy	11.5 J
Active Vibration Reduction	Yes
Service Indicator	Yes
Weight According to EPTA Procedure 01/2003	7.9 kg
Voltage	230 V
Frequency	50-60 Hz
Cord Length	4 m