How to release an accessory tool stuck in a Hilti TE 500-X?
If the accessory tool can’t be released from your Hilti Power Tool, make sure that you pull the chuck back as far as it will go and then remove the accessory tool.
How to release a chisel stuck in a Hilti TE 500-X Power Tool chuck?
If the chisel cannot be released from the chuck, ensure that the chuck is pulled back fully. Pull the chuck back as far as it will go and remove the insert tool.
Why does my Hilti TE 500-X not achieve full power?
If your Hilti Power Tool does not achieve full power, it could be due to an inadequate gauge (cross section) of the extension cord conductors. Use an extension cord with an adequate conductor cross section. Another cause could be that the control switch is not fully pressed. Ensure that you press the control switch as far as it will go.
What to do if there is no hammering action on my Hilti TE 500-X Power Tool?
If you're experiencing no hammering action with your Hilti Power Tool, it could be due to the tool being faulty or needing servicing. In this case, have the product repaired only by Hilti Service. Alternatively, the power tool might be too cold. Bring the tip of the accessory tool into contact with the workpiece and allow the power tool to run under no load until it reaches the minimum operating temperature.
Why doesn't my Hilti TE 500-X achieve full power?
If your Hilti Power Tool isn't reaching full power, consider these potential causes: * The gauge (cross section) of the extension cord conductors may be inadequate. Use an extension cord with an adequate conductor cross section. * The control switch may not be fully pressed. Ensure you press the control switch as far as it will go.
What to do if Hilti TE 500-X Power Tool doesn’t start and the service indicator lights red?
If your Hilti Power Tool doesn’t start and the service indicator is red, it could be due to worn-out carbon brushes. Have the power tool checked by a trained electrical specialist and the carbon brushes replaced if necessary. It also could be caused by a faulty tool, in that case the product should be repaired only by Hilti Service.
Why is there no hammering action in my Hilti Power Tool?
If there is no hammering action, the tool may be faulty or servicing is due. Have the product repaired only by Hilti Service.
How to troubleshoot a Hilti TE 500-X that doesn't start?
If your Hilti Power Tool doesn't start, there might be an interruption in the electrical supply. Try plugging in another power tool or appliance to check if the outlet works. The issue could also stem from a defective supply cord or plug, in which case you should have it checked and replaced by a trained electrical specialist. Another possibility is that the generator is in sleep mode; try applying a load to the generator by connecting a second power consumer, such as a work light. Finally, an electrical fault could be the culprit, so have the power tool and supply cables checked by a trained electrical specialist.
Essential safety instructions for handling power tools, covering work area, electrical, and personal safety.
Specific safety guidelines for breaker tools, including personal safety and dust handling.
Step-by-step guide on how to properly attach an accessory tool, including greasing and securing.
Instructions on how to safely detach an accessory tool from the breaker.
Instructions for cleaning the breaker, including precautions for air vents and casing.
A table listing common problems, their possible causes, and recommended actions.
Essential safety instructions for handling power tools, covering work area, electrical, and personal safety.
Specific safety guidelines for breaker tools, including personal safety and dust handling.
Step-by-step guide on how to properly attach an accessory tool, including greasing and securing.
Instructions on how to safely detach an accessory tool from the breaker.
Instructions for cleaning the breaker, including precautions for air vents and casing.
A table listing common problems, their possible causes, and recommended actions.
General| Hammer drilling diameter range | 12 - 40 mm |
|---|---|
| Dust removal system available | Yes |
| Working mode | Hammer drilling, Chiseling |
| Power input | 1600 W |
| Height | 210 mm |
| Voltage | 230 V |
| Frequency | 50 Hz |
| Cable Length | 4 m |
| Tool holder | SDS Max |
| Full hammering frequency | 2800 bpm |
| Optimum Hammer drilling diameter range | 16 - 32 mm |
| Blows per Minute | 2800 bpm |
To Next Page
