What to do if the service indicator lights red on Hilti TE 1000-AVR?
If the service indicator lights red on your Hilti Power Tool, the tool is faulty or servicing is due. Have the product repaired only by Hilti Service.
How to release a stuck chisel from the Hilti TE 1000-AVR Power Tool chuck?
If the chisel cannot be released from the chuck of your Hilti Power Tool, it might be because the chuck is not pulled back fully. Pull the chuck back as far as it will go and remove the insert tool.
Why my Hilti Power Hammer doesn't start?
If your Hilti Power Hammer doesn't start, it could be due to a few reasons. First, the electronics might be initializing, which can take up to 4 seconds, especially after a power interruption. Try switching the power tool off and then on again. Another possibility is an interruption in the electric supply. To check this, plug in another electric tool or appliance to see if it works. Lastly, if you're using a generator, it might be in sleep mode. To resolve this, apply a load to the generator by connecting another device, like a work light, and then switch the power hammer off and on again.
Why Hilti Power Hammer does not achieve full power?
If your Hilti Power Hammer does not achieve full power, there are several potential causes. One reason could be that the power reduction feature is active. To address this, press the power level selector switch, paying attention to the power level indicator. Additionally, try unplugging the power tool from the electric supply and then plugging it back in. Another possible cause is that the extension cord you're using is either too long or doesn't have a sufficient gauge. Ensure you're using an extension cord of an approved length and adequate gauge. Finally, the voltage from the electric supply might be too low. In this case, connect the power tool to a different power source.
Why is there no hammering action on my Hilti TE 1000-AVR Power Tool?
If there is no hammering action on your Hilti Power Tool, it could be because the power tool is too cold. Bring the tip of the accessory tool into contact with the working surface, switch the power tool on and allow it to run. If necessary, repeat the procedure until the hammering mechanism begins to operate.
How to troubleshoot no hammering action on Hilti TE 1000-AVR?
If you're experiencing no hammering action with your Hilti Power Tool, it might be because the tool is too cold. Bring the tip of the accessory tool into contact with the working surface, switch the power tool on, and let it run. Repeat this until the hammering mechanism starts to operate.
What to do if Hilti TE 1000-AVR switches off while running?
If your Hilti Power Tool switches itself off while running, it's likely that the overheating prevention cut-out has been activated. Allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
Why is the service indicator blinking red on my Hilti TE 1000-AVR Power Tool?
If the service indicator on your Hilti Power Tool is blinking red, it could be due to a couple of reasons. The voltage from the electric supply might be too high, so try using a different power outlet and check the electric supply. Alternatively, the overheating prevention cut-out may have been activated. In this case, allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
Why is the service indicator blinking red on my Hilti Rotary Hammer?
If the service indicator on your Hilti Rotary Hammer blinks red, it could be because the voltage provided by the electric supply is too high. Try using a different power outlet and check the electric supply. Alternatively, the overheating prevention cut-out might have been activated. In this case, allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
Why Hilti Rotary Hammer does not have full power?
If your Hilti Rotary Hammer does not achieve full power, it could be due to several reasons. The power reduction might be active. To solve this, press the power level selector switch, paying attention to the power level indicator. Also, unplug the power tool from the electric supply and then plug it back in. The extension cord might be too long or its gauge might be inadequate, so use an extension cord of an approved length and / or of adequate gauge. Finally, the voltage provided by the electric supply might be too low, so connect the power tool to a different power source.
Explains the meaning of DANGER, WARNING, CAUTION, and NOTE in safety instructions.
Explains the active vibration reduction system and protective features against damage and shock.
Covers overall safety advice, including warnings about following instructions and keeping the manual.
Details critical safety measures related to power cords, grounding, water exposure, and RCDs.
Outlines precautions for staying alert, using PPE, preventing unintentional starting, and proper attire.
Covers switching on/off, adjusting power, chiseling at low temperatures, and general chiseling techniques.
Provides specific advice on starting chiseling, direction, self-sharpening, depth, and contact pressure.
Lists common power tool issues, their possible causes, and recommended remedies.
Addresses further issues like generator sleep mode, cold operation, voltage problems, and tool unlocking.
General| Weight | 12.5 kg |
|---|---|
| Impact Energy | 26 J |
| Vibration Reduction | Yes |
| Tool Holder | TE-S |
| Weight according to EPTA Procedure 01/2003 | 12.5 kg |
| Full hammering frequency | 1950 impacts/minute |
| Power Source | Corded Electric |
| Voltage | 230 V |
| Blows per Minute | 1950 bpm |
| Dust removal system available | Yes |
| Impact Rate | 1950 impacts/minute |
To Next Page
