Hilti TE 1000-AVR User Manual (English)

Other manuals for Hilti TE 1000-AVR

Manual13 pages

Original Operating Instructions48 pages

Operation Instructions166 pages

Questions and Answers:

C
Carolyn HooperSep 4, 2025
Why is the service indicator blinking red on my Hilti Rotary Hammer?
- C
  Catherine FowlerSep 4, 2025
  If the service indicator on your Hilti Rotary Hammer blinks red, it could be because the voltage provided by the electric supply is too high. Try using a different power outlet and check the electric supply. Alternatively, the overheating prevention cut-out might have been activated. In this case, allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
G
gbuckAug 23, 2025
What to do if the chisel cannot be released from the chuck of Hilti Power Tool?
- M
  Mr. William Zavala DDSAug 23, 2025
  If the chisel cannot be released from the chuck of your Hilti Power Tool, it's likely that the chuck is not pulled back fully. Pull the tool lock back as far as it will go and then remove the insert tool.
D
Derek MarshallSep 1, 2025
Why Hilti Rotary Hammer does not have full power?
- M
  Mrs. Elizabeth Hoffman MDSep 2, 2025
  If your Hilti Rotary Hammer does not achieve full power, it could be due to several reasons. The power reduction might be active. To solve this, press the power level selector switch, paying attention to the power level indicator. Also, unplug the power tool from the electric supply and then plug it back in. The extension cord might be too long or its gauge might be inadequate, so use an extension cord of an approved length and / or of adequate gauge. Finally, the voltage provided by the electric supply might be too low, so connect the power tool to a different power source.
L
Lisa ComptonAug 31, 2025
Why doesn't my Hilti Rotary Hammer start?
- T
  thompsonmelissaSep 1, 2025
  If your Hilti Rotary Hammer doesn't start, it might be due to a few reasons. First, the electronics could be initializing, which can take up to 4 seconds after plugging in, especially if there was an interruption in the power supply. In this case, try switching the power tool off and then on again. Also, check for any interruptions in the electric supply by plugging in another electric tool or appliance to see if it works. If you're using a generator, it might be in sleep mode; try applying a load by connecting another device like a worklight, then switch the tool off and on again. Lastly, ensure the detachable supply cord is correctly fitted to the power tool.
C
Christopher ParrishAug 30, 2025
What to do if there is no hammering action on my Hilti Power Hammer?
- W
  Willie JohnsonAug 31, 2025
  If you're experiencing no hammering action with your Hilti Power Hammer, it might be because the power tool is too cold. To address this, bring the tip of the accessory tool into contact with the working surface, switch the power tool on, and allow it to run. If necessary, repeat the procedure until the hammering mechanism begins to operate.
R
Richard BaileyAug 29, 2025
How to release the chisel from the chuck of Hilti Power Hammer?
- J
  Joshua HamiltonAug 29, 2025
  If you can't release the chisel from the chuck of your Hilti Power Hammer, it's likely that the chuck isn't pulled back fully. Make sure to pull the chuck back as far as it will go to remove the insert tool.
A
aprilthomasAug 28, 2025
What does it mean if the service indicator blinks red on my Hilti Power Hammer?
- I
  Isabella CampbellAug 28, 2025
  If the service indicator on your Hilti Power Hammer blinks red, it could mean that the voltage from the electric supply is too high. Try using a different power outlet and check the electric supply. Alternatively, the overheating prevention cut-out might have been activated. In this case, allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
M
michael55Aug 27, 2025
What to do if my Hilti Power Hammer switches itself off while running?
- J
  julie41Aug 27, 2025
  If your Hilti Power Hammer switches itself off while running, it's likely that the overheating prevention cut-out has been activated. To resolve this, allow the tool to cool down and clean the air vents. Note that running the tool under no load is still possible even when this occurs.
H
Holly GonzalezAug 27, 2025
Why Hilti Power Hammer does not achieve full power?
- S
  Samuel GarciaAug 27, 2025
  If your Hilti Power Hammer does not achieve full power, there are several potential causes. One reason could be that the power reduction feature is active. To address this, press the power level selector switch, paying attention to the power level indicator. Additionally, try unplugging the power tool from the electric supply and then plugging it back in. Another possible cause is that the extension cord you're using is either too long or doesn't have a sufficient gauge. Ensure you're using an extension cord of an approved length and adequate gauge. Finally, the voltage from the electric supply might be too low. In this case, connect the power tool to a different power source.
J
Jesus MckenzieAug 25, 2025
Why my Hilti Power Hammer doesn't start?
- J
  johnsonchristinaAug 26, 2025
  If your Hilti Power Hammer doesn't start, it could be due to a few reasons. First, the electronics might be initializing, which can take up to 4 seconds, especially after a power interruption. Try switching the power tool off and then on again. Another possibility is an interruption in the electric supply. To check this, plug in another electric tool or appliance to see if it works. Lastly, if you're using a generator, it might be in sleep mode. To resolve this, apply a load to the generator by connecting another device, like a work light, and then switch the power hammer off and on again.

Hilti TE 1000-AVR Specifications

General

Weight	12.5 kg
Impact Energy	26 J
Vibration Reduction	Yes
Tool Holder	TE-S
Weight according to EPTA Procedure 01/2003	12.5 kg
Full hammering frequency	1950 impacts/minute
Power Source	Corded Electric
Voltage	230 V
Blows per Minute	1950 bpm
Dust removal system available	Yes
Impact Rate	1950 impacts/minute