Hioki IM3523A User Manual

Contents
ii
 Setting the Upper or Lower Limit Value as a
Percentage (%) Relative to a Reference Value
(Percentage mode) ................................. 98
 Setting Upper and Lower Limit Values as (%)
Values Relative to the Offset from the
Reference Value
(Deviation Percentage Mode) ................ 101
4.5 Setting Application Settings ..............104
4.5.1 Synchronizing Measurement
(Trigger Synchronous Output Function)
..........................................................104
4.5.2 Saving Measurement Results
(Memory function) ............................106
4.5.3 Detecting OPEN during 2-terminal
Measurement (HIGH-Z Reject Function)
..........................................................108
4.5.4 Monitoring the Detection Level
(Monitoring the Detection Level Function)
..........................................................110
4.5.5 Setting the Detection Sensitivity for Mea-
surement Errors (Overflow or Underflow)
..........................................................113
4.5.6 Setting the Delay Time from the Output of
Comparator and BIN Judgment Results
until Output of EOM
(LOW) and Resetting
Judgment Results ............................115
4.5.7 Enabling Trigger Input for during Mea-
surement and Setting the Valid Edge of
Trigger Input .....................................117
4.5.8 Setting the EOM
Output Method ......119
4.5.9 Disabling Key Operation
(Key-lock Function) ..........................121
4.5.10Setting the Number of Display Digits 124
4.5.11Enlarging Display of Measurement
Values ..............................................126
4.5.12Setting the LCD to ON/ OFF ............127
4.5.13Setting Operation Sounds
(Beep Sounds) .................................128
4.5.14Initializing (System Reset) ...............129
Chapter 5 ANALYZER
Function 131
5.1 About ANALYZER function ..............131
5.1.1 Initial screen .....................................132
5.2 Setting Basic Settings of Measurement
..........................................................133
5.2.1 Setting the measurement parameter 133
5.2.2 Setting the Sweep Parameter ..........135
5.2.3 Setting the Trigger ........................... 137
5.2.4 Setting the Display Timing ............... 139
5.2.5 Setting the Trigger Delay ................. 140
5.2.6 Segment Setting .............................. 142
5.3 Normal Sweep ................................. 143
5.3.1 Setting Sweep Points ....................... 143
5.3.2 Setting the Measurement Signal ...... 157
5.3.3 Setting the Measurement Range ..... 160
 Setting AUTO Ranging ........................... 160
 Setting the Ranging to HOLD ................. 162
5.3.4 Setting the Measurement speed ...... 164
5.3.5 Displaying as Average Values
(Average set) ................................... 165
5.3.6 Setting the Point Delay .................... 166
5.3.7 Setting the DC Bias ......................... 167
5.4 Segment Sweep .............................. 169
5.4.1 Select Segments .............................. 169
5.5 Setting the Graph Display Method ... 176
5.5.1 Setting the Horizontal Axis ............... 176
 Overwrite Setting .................................... 176
 Horizontal Axis Scale Setting ................. 177
 Span Setting ........................................... 179
5.5.2 Setting the Vertical Axis ................... 181
 Draw Color Setting ................................. 181
 Vertical Axis Scale Setting ..................... 183
 Manual Scaling Setting .......................... 184
5.5.3 Setting Grid Display ......................... 186
5.6 Checking the Measurement Values . 188
5.6.1 Setting the Cursor ............................ 188
 Cursor Display Setting ........................... 189
 Cursor Move Setting .............................. 190
 Search Function Setting ......................... 190
 Search Target Parameter Setting .......... 191
 Option setting ......................................... 191
 Auto Search Setting ............................... 192
5.6.2 Moving the Cursor ........................... 193
5.6.3 Performing Measurement Value Search
.......................................................... 194
5.7 Judging Measurement Results
(Comparator Function) ..................... 197
 Area Judgment ....................................... 197
 Peak Judgment ...................................... 208
5.8 Editing Judgment Points .................. 217
5.9 Application Settings ......................... 219
5.9.1 Saving Measurement Results
(Memory function) ............................ 219

Hioki IM3523A Specifications

General

Brand	Hioki
Model	IM3523A
Category	Measuring Instruments
Language	English