English
–
21
–
EN
RECORDING FUNCTION
Now, compare the channel numbers you have written in the
GUIDE Channel and VCR Channel columns. You must set all
of these channel numbers that don't match using the follow-
ing procedure before you programme the automatic timer
recording using the SHOWVIEW system.
• This setting only needs to be set once, but must be
done again if you use this DVD/VCR in another area by
moving it.
Press MENU.
Press
K or L to select “INITIAL”,
then press B.
Press K or L to select “GUIDE
CHANNEL”, then press B.
Press K or L to select the rele-
vant mode, then press B.
•
To set the guide channel individu-
ally, select “MANUAL”. Then, press
B and continue with step .
•To set all the guide channels to
AV1, AV2 or AV3, select “AV1”, “AV2” or “AV3”. Then
press MENU to exit.
• If you are recording from a Digital Satellite or Terrestrial
Set Top Box the channel should be set to AV2 (or is
connected to).
Press K or L repeatedly to select the position number,
then press B.
Press the number buttons or (K
or L) to enter
guide channel num-
ber, then press B.
• Press s to erase all digit.
•You can select guide channels
1-255.
•To select channels from 1-9, first
press 0 twice, and then 1 to 9.
•To select channels from 10 to 99, first press 0 once,
and then press the last two digits. (To select channel
80, first press 0, then press 8 and 0.)
•To set another, repeat steps to .
Press MENU to exit.
7
65
6
5
5
4
3
2
1
You can programme the timer using the SHOWVIEW program-
ming numbers that are printed in TV guide magazine. You
can set eight programmes to record.
• Use the remote control for the this procedure.
• Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
Press the SHOWVIEW button.
If you have not set the clock yet,
“CLOCK” setting menu appears. If
so, follow the steps outlined in the
“Setting the Clock” section. Then, set the timer.
1
VCR
Timer Recording using the SHOWVIEW System
The VPS/PDC system looks for the start signal several hours
before published start time and for several hours afterwards.
This means that if the programme is broadcast anytime dur-
ing this period it will be recorded correctly. Please note that if
you have set an incorrect Timer setting, it will stay in the
memory until you cancel it (see page 20 for details on how to
cancel a programme).
VCR
VPS (Video Programme System) /
PDC (Programme Delivery Control)
When timer recording is finished, the DVD/VCR will automati-
cally rewind the tape to the beginning where it started
recording. If there are any remaining programmes including
Daily, Everyday, & Weekly, AUTO RETURN will not operate.
VCR
Auto Return
Press the number buttons to set
the SHOWVIEW number of the pro-
gramme you want to record.
• Press
s to go back one digit
from current digit while you set the S
HOWVIEW number.
Select once, daily, everyday, or weekly recording.
For once-only recording: Press the SHOWVIEW button.
For daily recording: To record a TV programme at the
same time on the same channel from Monday through
Friday. Press DAILY/WEEKLY repeatedly to select
“DAILY (MO-FR)”, then, press the SHOWVIEW button.
For everyday recording: To record a TV programme at
the same time on the same channel every day. Press
DAILY/WEEKLY repeatedly to select “DAILY (MO-SU)”,
then, press the
SHOWVIEW button.
For weekly recording: To record a TV programme at
the same time on the same channel every week.
Press
DAILY/WEEKLY repeatedly to select “WEEKLY”,
then, press the SHOWVIEW button.
NOTES:
•
If the SHOWVIEW number is not available, it will be cleared
automatically when you press the SHOWVIEW
button
.
Enter the correct SHOWVIEW number and press the
SHOWVIEW
button
again.
• If the SHOWVIEW number flashes when you press the
SHOWVIEW button, this means that the SHOWVIEW num-
ber you entered was incorrect or the timer recording you
just programmed and another timer recording overlap.
Confirm the channel number, then, press B.
• If your local channel information
is programmed in DVD/VCR’s
memory, your local channel
number appears automatically.
•
If your local channel information is
not programmed in DVD/VCR’s
memory, “– –” or an incorrect
channel number may appear. In this case, press K or L
repeatedly until your desired channel number appears.
Then, press s.
• When you select the channel number using K or L it
memorises in DVD/VCR’s memory.
Press K or L repeatedly until the desired tape speed
appears.
Press K or L to choose “ON” or
“OFF”.
• The Video Programme System
(VPS) / The Programme
Delivery Control (PDC) is a very
convenient system which
assures that the TV programmes you have pro-
grammed for timer recording will be recorded exactly
from beginning to end. (Refer to next column.)
Press MENU to exit.
Press TIMER to activate the timer. The TIMER light on
the display comes on.
8
7
6
5
4
3
2
To Next Page
Loading...
