To Next PageTo Next Page
Need help?Do you have a question about the Honda BF2.3D and is the answer not in the manual?
General| Fuel Delivery | Carburetor |
|---|---|
| Lubrication | Splash |
| Fuel Tank Capacity | 1.0 L |
| Gear Ratio | 2.08:1 |
| Displacement | 57 cc |
| Max Output | 2.3 HP |
| Full Throttle RPM Range | 5000 - 6000 rpm |
| Cooling System | Water-cooled |
| Ignition System | Transistorized |
| Starting System | Recoil |
| Propeller | 3-Blade |
| Dry Weight | 27 kg |
Explains various forms of safety information provided in the manual.
Highlights the importance of using the motor safely and following manual instructions.
Details the operator's duties for safe operation and emergency preparedness.
Provides precautions for refueling gasoline safely.
Warns about the dangers of carbon monoxide from exhaust.
Shows the location and meaning of safety labels on the motor.
Information specific to safety labels for Canadian models.
Explains how to interpret type codes to identify control and feature applications.
Illustrates and labels the various components and controls of the outboard motor.
Details the function and use of the emergency stop switch system.
Explains the operation of the choke knob for engine starting.
Describes how the throttle grip controls engine speed.
Explains how to adjust throttle grip resistance for speed holding.
Details the operation of the fuel valve lever to control fuel flow.
Explains how to operate the starter grip for engine cranking.
Describes the function of the strap that secures the engine cover.
Explains how to adjust the transom angle of the outboard motor.
Describes how to use the tilt lever for positioning the outboard motor.
Details how to adjust the steering friction for resistance.
Explains how to use clamp screws to secure the motor to the transom.
Describes the function of the fuel filler cap vent knob.
Covers features like the centrifugal clutch, oil level window, and anode.
Details the horsepower requirements for installing the outboard motor.
Guides on the correct mounting position and height of the outboard motor.
Explains how to attach the outboard motor to the boat's transom.
Describes the procedure for adjusting the transom angle of the outboard motor.
Emphasizes safety and knowledge preparation before operating the motor.
Covers essential safety precautions like wearing a PFD and using the kill switch.
Outlines pre-operation checks for safety and equipment longevity.
Lists essential maintenance checks before operating the motor.
Details crucial safety checks to perform before each use.
Provides guidelines for safe operation and understanding controls.
Explains the recommended break-in procedure for optimal performance and life.
Details how to adjust the transom angle for proper propeller operation.
Provides advice for users who operate the motor infrequently.
Step-by-step instructions for starting the outboard motor.
Provides instructions for starting the engine manually with an emergency starter rope.
Details procedures for emergency and normal engine stopping.
Explains how to use the throttle grip and friction knob for speed control.
Provides instructions and safety precautions for operating the motor in reverse.
Explains how to steer the boat using the tiller handle and adjust steering friction.
Offers advice on engine speed and transom angle for efficient cruising.
Details procedures for tilting the motor for mooring, beaching, or launching.
Stresses the necessity of proper maintenance for safety and longevity.
Lists critical safety precautions to follow during maintenance and repairs.
Identifies the tools supplied with the motor for maintenance and emergencies.
Provides a detailed schedule for routine inspections and maintenance.
Explains the procedure for removing and installing the engine cover.
Details how to check the engine oil level using the inspection window.
Provides a step-by-step guide for changing the engine oil.
Recommends the appropriate type and viscosity of engine oil.
Outlines the procedure for changing the gear case oil.
Identifies lubrication points and intervals for grease and corrosion inhibitor.
Details how to inspect, gap, and replace the spark plug.
Provides essential safety precautions and steps for refueling the motor.
Specifies the recommended type of unleaded gasoline and octane rating.
Advises on inspecting and replacing the recoil starter rope.
Explains when and how to replace the anode for corrosion protection.
Details the procedure for replacing the propeller, including safety precautions.
Outlines steps for preparing the motor for storage to ensure trouble-free operation.
Guides on using fuel stabilizer to prevent fuel deterioration during storage.
Explains how to drain the fuel system to avoid deterioration.
Details engine oil preparation for storage, including changing oil and preparing the cylinder.
Advises on selecting a suitable storage area and positioning the motor.
Guides on checking the motor after storage before operation.
Provides guidance for trailering a boat with the outboard motor attached.
Explains how to transport the outboard motor after removing it from the boat.
Lists possible causes and corrections for engine starting issues.
Addresses common issues of hard starting or stalling after the engine begins running.
Troubleshoots why the engine might not be driving the propeller.
Provides immediate service steps for a motor that has been submerged in water.
Guides on where to find product and engine serial numbers for record-keeping.
Explains carburetor adjustments for optimal performance at higher altitudes.
Discusses the sources of emissions and Honda's control systems.
Warns against tampering with the emission control system.
Lists symptoms that might indicate emission-related problems.
Recommends using genuine Honda parts for emission system maintenance.
Explains the meaning and significance of the Star Label for cleaner marine engines.
Provides detailed technical specifications for the BF2.3D model.
Lists available Honda publications for maintaining and repairing the outboard motor.
Describes the illustrated parts catalog and how to obtain it.
Highlights the range of accessories available to enhance the boating experience.
Provides information on contacting Honda for support and addressing concerns.
Outlines the types of warranties provided for the outboard motor.
Explains how to obtain warranty service and what to expect.
Details the limited warranty terms for the United States, Puerto Rico, and Virgin Islands.
Specifies the conditions and requirements to qualify for the warranty.
Clarifies what parts or labor are covered under the warranty.
Lists specific conditions and actions that are not covered by the warranty.
Outlines limitations on consequential damages and implied warranties.
Explains the warranty coverage for the engine's emission control system.
Details the owner's responsibilities for maintaining warranty validity.
Specifies warranty periods for emissions compliance.
Lists the specific parts covered under the emission control system warranty.
Details the distributor's warranty for products purchased and operated in Canada.
Lists items and conditions not covered by the Canadian warranty.
Outlines the owner's obligations to maintain the Canadian warranty.
Covers the warranty for genuine Honda replacement parts and accessories.
States that the provided warranties are the only ones applicable.
