Honeywell FG8MS User Manual

32318167-001 Rev.A
> 2.1m (7')
> 1m
(3')
<
7.6m (25')
> 3m
(10')
SENS1 SENS2
V2GY/ALPHA
SENS1 SENS2
V2GY/ALPHA
ALPHA
V2GY
LEDs de signalisation
Indicadores LED
LED-Anzeigen
LED-indicatoren
Indicatori LED
LED Indicators
Switch d'AP capot
Tamper frontal
Deckelkontakt
Deksel sabotageschakelaar
Tamper anteriore
Front Tamper Switch
SENS1 SENS2
V2GY/ALPHA
SENS1 SENS2
V2GY/ALPHA
SENS1 SENS2
V2GY/ALPHA
SENS1 SENS2
V2GY/ALPHA
Couverture / Covertura /
Erfassungbereich /
Bereik / Portata / Range
Interrupteur " test "
de bris de vitre
Test de prueba de rotura
de cristal
Glasbruch-Testschalter
Testschakelaar glasbreuk
Di test rottura vetri
Glassbreak Test Switch
Protocole / Protocolo /
Protokoll / Protocol /
Protocollo / Protocol
100% 40%
60% 20%
CR-123A
CR-123A
3.5 mm x 38 mm
(#6 x 1-1/2")
#6 (3.5 mm)
AP à l'arrachement
Tamper posterior
Abreißsicherung
Muur
sabotageschakelaar
Tamper posteriore
Rear Tamper
Avertissement : Remplacer les deux
piles en même temps, uniquement avec:
Advertencia: Sustituya ambas
baterías al mismo tiempo y sólo por:
Achtung: Beide Batterien gleichzeitig
und nur durch folgenden Typ ersetzen:
Waarschuwing: vervang beide
batterijen gelijktijdig en alleen met:
Attenzione: sostituire entrambe le
batterie contemporaneamente
utilizzando esclusivamente:
Warning: Replace both batteries
at the same time, and only with:
CR-123A
CR-123A
Languette
Cierre
Verriegelung
Vergrendeling
Chiusura a scatto
Latch
Si necessaire, Pré-perçage pour la vis de fixation*
Si necesario, Preorificio para el tornillo de la carcasa frontal*
Wenn erforderlich, Ausbrechstück für Gehäuseschraube*
Indien Nodig, Uitbreekgat voor dekselschroef*
Si necessario, Predisposizione foro per la vite del coperchio*
If Required, Break Out Flash for Cover Screw*
* 2.9 mm x 6 mm (#4 x 1/4")
Panasonic CR123A /
Duracell DL123 /
Duracell DL123A
FG8MS
Optimal / Óptimo / Optimal / Optimaal / Ottimale / Optimal
Satisfaisant / Satisfactorio / Zufriedenstellend / Voldoende / Suciente / Satisfactory
Non / No / Nein / No / No / No
A
B
C D

Honeywell FG8MS Specifications

General

Brand	Honeywell
Model	FG8MS
Category	Security System
Language	English

Summary

Mounting Location and Range Guidelines

Detection Range Settings

Details the various detection range settings and optimal placement for the FG8MS detector.

Protocol Selection

Explains how to select the communication protocol for the detector.

LED Indicator Functions

Describes the functions and meanings of the device's LED indicators.

Tamper Switch Operation

Details the front and rear tamper switch mechanisms for security.

Glassbreak Test Switch

Explains the operation and purpose of the glassbreak test switch.

Installation and Setup Procedures

Mounting Detector Guidelines

Provides instructions on selecting the mounting location and orienting the detector.

Test Modes and LED Indicators

Details the Transmitter and Glassbreak test modes and their corresponding LED feedback.

Testing Without FG-701 Tester

Describes how to test the glassbreak function using ambient noise and physical tapping.

Detector Registration

Instructions on how to register the FG8MS detector with the system.

Cover Screw Installation

Guidance on securing the detector's front cover with a screw.

Technical Specifications

Power and Battery Information

Details power source, low battery threshold, and expected battery life.

RF and Detection Range

Specifies RF frequency, range, and detection range characteristics.

Operating Environment

Lists operating and storage temperature, and humidity specifications.

Physical Dimensions and Weight

Provides physical dimensions and weight for the sensor and packaged unit.

Battery Safety Warnings

Crucial safety warnings and handling instructions for batteries.