JADE™ ECONOMIZER MODULE
21 63-2700—05
SETPOINTS MAT SET 53ºF 38 to 70 ºF;
increment by 1
Setpoint determines where the economizer will
modulate the OA damper to maintain the mixed air
temperature.
LOW T LOCK 32ºF -45 to 80 ºF;
increment by 1
Setpoint determines outdoor temperature when the
mechanical cooling cannot be turned on.
Commonly referred to as the Compressor lockout.
DRYBLB SET 63ºF 48 to 80 ºF;
increment by 1
Setpoint determines where the economizer will
assume outdoor air temperature is good for free
cooling; e.g.; at 63 ºF unit will economizer at 62 ºF
and below and not economize at 64 ºF and above.
There is a a 2 ºF deadband.
ENTH CURVE ES3 ES1, ES2, ES3,
ES4, or ES5
Enthalpy boundary “curves” for economizing using
single enthalpy.
See “Enthalpy Settings” on page 17 and Product
Data sheet form 63-2700 for description of
enthalpy curves.
DCV SET 1100ppm 500 to 2000 ppm
increment by 100
Displays ONLY if a CO2 sensor is connected.
Setpoint for Demand Control Ventilation of space.
Above the setpoint, the OA dampers will modulate
open to bring in additional OA to maintain a space
ppm level below the setpoint.
MIN POS 2.8 V 2 to 10 Vdc Displays ONLY if a CO2 sensor is NOT connected.
With 2-speed fan units MIN POS L (low speed fan)
and MIN POS H (high speed fan) settings are
required. Default for MIN POS L is 3.2V and MIN
POS H is 2.8V
VENTMAX 2.8 V 2 to 10 Vdc
or
100 to 9990 cfm
increment by 10
Displays only if a CO2 sensor is connected.
Used for Vbz (ventilation max cfm) setpoint.
Displays 2 to 10 V if <3 sensors (RA,OA and MA).
With 2-speed fan units VENTMAX L (low speed fan)
and VENTMAX H (high speed fan) settings are
required. Default for VMAX L is 3.2V and VENTMAX
H is 2.8 V
VENTMIN 2.25 V 2 to 10 Vdc
or
100 to 9990 cfm
increment by 10
Displays only if CO2 sensor is connected.
Used for Va (ventilation min cfm) setpoint.
Displays 2 to 10 V if <3 sensors (RA,OA and MA).
Va is only set if DCV is used. This is the ventilation
for less than maximum occupancy of the space.
With 2-speed fan units VENTMIN L (low speed fan)
and VENTMIN H (high speed fan) settings are
required. Default for VENTMIN L is 2.5V and
VENTMIN H is 2.25V
ERV OAT SP 32ºF 0 to 50 ºF;
increment by 1
Only when AUX1 O = ERV
EXH1 SET 50% 0 to 100%;
increment by 1
Setpoint for OA damper position when exhaust fan
1 is powered by the economizer.
With 2-speed fan units Exh1 L (low speed fan) and
Exh1 H (high speed fan) settings are required.
Default for Exh1 L is 65% and Exh1 H is 50%
EXH2 SET 75% 0 to 100%;
increment by 1
Setpoint for OA damper position when exhaust fan
2 is powered by the economizer. Only used when
AUX1 O is set to EHX2.
With 2-speed fan units Exh2 L (low speed fan) and
Exh2 H (high speed fan) settings are required.
Default for Exh2 L is 80% and Exh2 H is 75%
a
ERV Operation: When in Cooling mode AND the conditions are NOT OK for economizing - the ERV terminal will be energized. In
the Heating mode the ERV terminal will be energized when the OA is below the ERV OAT setpoint in the setpoint menu.
Table 7. Setup and Setpoint Menus. (Continued)
Menu Parameter
Parameter
Default
Value
Parameter
Range and Increment Notes
To Next Page
Loading...
