Horizon Hobby Blade 700X

Questions and Answers

D
Devon SmithAug 3, 2025
Why won't my Horizon Hobby Toy helicopter respond to the throttle?
- D
  derek56Aug 3, 2025
  If your Horizon Hobby Toy helicopter responds to other controls but not the throttle, start by ensuring the throttle stick is at idle and the throttle trim is not too high; lower them if needed. Verify that the transmitter is in normal mode and throttle hold is off. Check the connection between the motor wires and the ESC, inspecting the wires for any damage. Also, ensure the flight battery is adequately charged; replace or recharge it if necessary. Finally, confirm that the throttle channel is not reversed on the transmitter; if it is, reverse it.
D
Deborah SmithAug 7, 2025
What to do if the Horizon Hobby Toy aircraft won't bind and the LED flashes rapidly?
- D
  Dawn LoweAug 7, 2025
  If the LED on the receiver flashes rapidly and your Horizon Hobby Toy aircraft won't bind to the transmitter during binding, there are a few potential causes. First, the transmitter might be too close to the aircraft during the binding process. Power off the transmitter, move it further away from the aircraft, disconnect and reconnect the flight battery, and then follow the binding instructions again. Another possibility is that the bind switch or button wasn't held while the transmitter was powered on. Power off the transmitter and repeat the bind process, ensuring the bind switch is held. Lastly, the aircraft or transmitter could be too close to a large metal object, wireless source, or another transmitter. Move both to a different location and try binding again.
A
andersondouglasAug 11, 2025
Why does the tail of my Horizon Hobby Toy helicopter spin out of control?
- W
  William JacksonAug 11, 2025
  If the tail of your Horizon Hobby Toy helicopter spins out of control, several factors could be responsible. Begin by ensuring that the rudder control and sensor are operating in the correct direction. Next, inspect the tail servo for any damage and replace it if necessary. Also, check the tail drive gears for damage and replace them if needed. Make sure the rudder control arm has adequate travel and adjust if necessary. Finally, ensure the torque tube is fully engaged in the tail gears. Confirm the tail pushrod length and tail settings on AR7200BX are correct after making any changes.
S
Steven ClayAug 15, 2025
Why does my Horizon Hobby Toy helicopter wobble in flight?
- J
  Justin NguyenAug 15, 2025
  If your Horizon Hobby Toy helicopter wobbles during flight, it could be due to several reasons. The cyclic gain might be too high; in that case, decrease Dial 1 on the AR7200BX. Another cause could be that the head speed is too low; increase the helicopter's head speed via your transmitter settings or by using a freshly charged flight pack. Lastly, worn dampers can cause wobbling; replace the main rotor head dampers.
B
Brenda Owens DDSAug 20, 2025
How to fix a Horizon Hobby Toy helicopter that will not lift off?
- W
  william21Aug 20, 2025
  If your Horizon Hobby Toy helicopter won't lift off, there are a few things to check. First, ensure that the transmitter settings are correct, specifically the throttle and pitch curve settings, and the pitch control direction. Also, make sure the flight battery has sufficient voltage by fully charging it. Finally, verify that the main rotor blades are installed correctly, with the thicker side as the leading edge.
A
aburtonAug 25, 2025
Why will my Horizon Hobby Toy's AR7200BX not initialize?
- K
  Kelly GardnerAug 25, 2025
  If the AR7200BX on your Horizon Hobby Toy does not initialize, it could be due to a few reasons. If the helicopter was moved during initialization, lay it on its side during initialization, especially if it's windy. Ensure the transmitter is powered on. Also, make sure the elevator, aileron, and rudder controls are centered, and the throttle is at idle.
G
Gary MurrayOct 29, 2025
What to do if the LED flashes rapidly and the Horizon Hobby Toy aircraft won't respond after binding?
- J
  Jennifer ChenOct 29, 2025
  If the LED on the receiver flashes rapidly and your Horizon Hobby Toy aircraft doesn't respond to the transmitter after binding, there might be several reasons. First, ensure you wait at least 5 seconds after powering on the transmitter before connecting the flight battery to the aircraft. If using a ModelMatchTM radio, verify that the correct model memory is selected on the transmitter. Also, check the charge level of both the flight and transmitter batteries, replacing or recharging them if necessary. The transmitter may have been bound to a different model or with a different DSM Protocol, so select the right transmitter or bind to the new one. Finally, make sure that the aircraft and transmitter aren't too close to large metal objects, wireless sources, or other transmitters; if so, mo...