Horton C2150 - C2150 Initialization for Linear Drives; Performing the Learn Cycle; Checking Door Cycle Operation

-A full learn cycle can not be completed with this security parameter in place.
Consult your supervisor or the factory for authorization and instructions on how to remove
this security parameter.
In version 1.17 and later, the display will show
SU
-If
SU
does not appear, then the control was not
properly reset into the full learn mode (Go back
to step 2)
-If the display flashes
nA
like an error code,
The
nA
(
n
o
A
ccess) parameter has been
turned on.
-The control will display
ONE
of the following
lock codes depending the type of lock
connected. (see Section 6)
-The display should "blink" the version number
(as in 1 then 17)
When the toggle switch is on, the
DOWN
button acts as an actuation device.
The door will move
- Be sure the safety beam area is clear of obstructions.
Activation devices should not yet be installed.
4th Step -Checking door cycle
10/05 1.0013d
*LOCK CODES
Y
Fail Safe
Autolock
R
+100
OR
LOCK
O
Y
LOCK
MON
No
Autolock
OR
+100
+100
R
R
R
+100
+100
R
LOCK
MON
Fail Secure
Autolock
O
LOCK
LOCK
MON
O
LOCK
Y
THEN
O
Y
Y
O
LOCK
LOCK
MON
Y
LOCK
MON
+100
R
LOCK
LOCK
MON
LOCK
O
2. C2150 INITIALIZATION
Instruct the control to perform a full learn cycle by:
-Holding down the
SET
button and the
RESET
button.
-Release the
RESET
button.
-Hold the
SET
button for an additional 5 seconds
then release.
Be sure the toggle circuit is completed and apply
AC power to the unit.
CAUTION: THE DOOR WILL MOVE.
VERSION 1.00 and earlier
The display should "blink" the version number
(as in 1 then 00) *The display will show the lock
code (see below)
2nd Step - Learn cycle
3rdStep-Versiondisplay
VERSION 1.17 and LATER
1st Step - Power up
SET
R
+100
R
+100
O
LOCKLOCK
R
O
O
LOCK
MON
LOCK
MON
THEN
LOCK
MON
LOCK
Y
Y
+100
Y
RESET
H201C.2
-If the above cycle check is OK and there are no parameters to be changed or an
autolock to setup, this concludes the C2150 initialization.
Ver 1.17 or later
IF THERE IS ANY DIFFICULITY SEE APPENDIX A
The closing speed should not exceed the rate of
1 ft / sec
R
OR
-The display returns to:
Ver 1.00 to 1.16
+100
-C
lose
C
heck
-C
lose c
U
shion
-Time
D
elay
-C
lose
S
peed
Close Cycle
R
+100
+100
R
R
+100
+100
R
+100
R
Inspect the unit for smooth operation, free of binds and excessive noise.
OR
Start with the door in the closed position.
Press the
DOWN
button to actuate the door to open at factory selected
default settings.
The chart below shows the position of the door and the display code for each position.
-The display starts with:
*
Braking may overide open check display
-O
pen c
U
shion
-O
pen
C
heck
*
-O
pen
S
peed
-Motor Braking
Open Cycle
Ver 1.00 to 1.16
The follow cycles are
carried out automatically
by the C2150 control
R
+100
+100
R
+100
R
+100
R
R
+100
Ver 1.17 or later
UP
+100
R
DOWN
SET