Hotspot RELAY User Manual

Hot Spot Spa Pre-Delivery Instructions
Pre-Delivery Instructions
Please take the time to read this booklet carefully, as it will provide you with the information you will need to ensure
the safe, secure, and timely installation of your new spa. The following sections are guidelines on how to prepare for
delivery and set-up of your new spa. Specifically covered are site selection, delivery access, ground preparation, and
electrical requirements.
Remember to carefully read the Owner’s Manual that accompanies your spa, and to complete the warranty register
within 10 days of delivery. These items, along with other valuable information, will be found in the Owner’s Package
which has been placed in the equipment compartment of your spa, where you will also find its serial number.
Watkins Manufacturing Corporation reserves the right to change features, specifications and design without
notification and without incurring any obligation.
DATE PURCHASED: _________________________________________________________________
DATE INSTALLED: ___________________________________________________________________
DEALER: ___________________________________________________________________________
ADDRESS: __________________________________________________________________________
TELEPHONE: _______________________________________________________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of
exterior surfaces (decks and gazebos). In addition, some communities have adopted residential barrier codes which
may require fencing and/or self-closing gates on the property to prevent unsupervised access to a pool (or spa) by
children under 5 years of age. Your Hot Spot spa is equipped with a locking cover that meets the ASTM F1346-91
Standard for Safety Covers and as a result, is usually exempt from most barrier requirements. As a general practice,
your local Building Department will inform you of any applicable barrier requirements at the time a permit is obtained
for the installation of an electrical circuit. Your Hot Spot dealer can provide information on which permits may be
required.
Congratulations on your decision to enjoy the finest spa available.
Welcome to the growing family of Hot Spot
®
Spa owners.
Register your warranty
using the QR code below:

Hotspot RELAY Specifications

General

Series	Hot Spot
Heater	4kW
Manufacturer	Hot Spring
Dimensions	84" x 84" x 34"
Jet Count	23
Jet Pump 1	1.5 HP
Pump	1.5 HP
Filtration	75 sq ft
Water Volume	290 gallons
Dry Weight	500 lbs
Weight (Empty)	500 lbs
Filled Weight	3, 500 lbs
Lighting System	LED
Frame Material	Polymer
Warranty	5 years

Summary

Document Introduction and Pre-Installation Information

Warranty and Dealer Details

Information on registering your warranty and recording dealer contact details.

Permitting and Local Codes

Guidance on local permits for electrical work and barrier codes for safety.

Site Selection and Installation Preparation

General Site and Surface Requirements

Ensure a level, sound surface, and access to equipment and breakers.

Outdoor and Indoor Installation Specifics

Considerations for outdoor patios, decks, and indoor placement regarding flooring and drainage.

Delivery Access Planning

Measuring Clearances for Delivery

Determine required path width and height using spa dimensions and cart.

Obstacles and Delivery Methods

Identify potential obstructions and options like cranes for challenging deliveries.

Ground Preparation and Foundations

Recommended Foundation Types

Concrete pads or structurally sound decks are preferred for stability.

Foundation Installation Notes

Tips on using stepping stones, avoiding settling, and managing debris.

Spa Model Dimensions

Tempo (TEM) Dimensions

Detailed technical drawings and dimensions for the Tempo spa model.

Relay/Rhythm (REL/RHY) Dimensions

Detailed technical drawings and dimensions for the Relay and Rhythm spa models.

SX (SX) Dimensions

Detailed technical drawings and dimensions for the SX spa model.

TX (TX) Dimensions

Detailed technical drawings and dimensions for the TX spa model.

Electrical Requirements and Wiring

Voltage Selection and Heater Output

Understand voltage options (115V/230V) and their impact on heater performance.

115 Volt Cord-Connected Configuration

Requirements for 115V GFCI outlets, including placement and testing.

115 Volt 20 Amp Requirements (SX Model)

Details for dedicated 115V, 20A GFCI circuits and proper wiring.

115 Volt 30 Amp Conversion (SX/TX)

Guidelines for converting SX and TX models to 115V, 30A service.

230 Volt Installation (All Models)

Requirements for 230V installation, including subpanels and GFCI protection.

Contractor and Service Information

Electrician and General Contractor Suggestions

Space to record contact information for qualified electricians and general contractors.

Available Dealer Services

Details on pre-delivery, installation, operation, and maintenance services offered by the dealer.

Additional Products and Spa Specifications

Additional Products Available

List of optional spa care systems, accessories, and retractable cover systems.

Spa Specifications Overview

Key technical specifications including dimensions, capacity, weight, and electrical needs for each model.