HP ProLiant ML110 G7 User Manual (English)

Other manuals for HP ProLiant ML110 G7

Maintenance And Service Guide96 pages

Product End-Of-Life Disassembly Instructions6 pages

Questions and Answers:

E
Edward AllenJul 26, 2025
How to fix HP ProLiant ML110 G7 Server that does not boot installed OS?
- R
  Robert DixonJul 26, 2025
  If your HP Server does not boot a previously installed operating system, it could be due to a corrupted operating system. In this case, repair or reinstall the operating system. Another potential cause is a problem with the hard drive subsystem, so check and resolve any issues there. Finally, verify and correct the boot order setting in RBSU, as an incorrect setting can prevent the system from booting correctly.
C
Caitlin PerryAug 3, 2025
What to do if HP ProLiant ML110 G7 does not power on?
- A
  adam95Aug 3, 2025
  If your HP Server doesn't power on, here are a few things to check: * First, check the power supply. Make sure it's properly seated. Reseat it if necessary. * Next, ensure the power cord is securely connected. * Then, verify the power source is working. * Inspect the power on circuit. * Also, make sure all components are properly seated. If none of these steps work, there may be a faulty internal component. You’ll need to identify and replace it.
C
Chad StewartAug 10, 2025
Why does my HP ProLiant ML110 G7 Server report fault events after booting?
- R
  Raymond GregoryAug 10, 2025
  If your HP Server boots, but Insight Management Agents report a fault event, the issue could be due to several reasons. First, check all internal and external components to ensure they are properly seated; reseat them or replace any faulty components. Another potential cause is an unsupported component being installed, so remove any such components. Redundancy failures can also trigger these events, so investigate and resolve any such failures. Finally, a system overtemperature condition could be the cause, so check the system temperature and resolve any overheating issues.
K
Kenneth BellAug 17, 2025
What to do if HP Server does not complete POST?
- M
  Monica HaasAug 17, 2025
  If your HP Server doesn't complete POST, the issue might be due to an improperly seated or faulty internal component. Reseat or replace any such components. Another possible cause is a faulty KVM device; check it for faults. Additionally, inspect the video device for faults and replace it if necessary.

HP ProLiant ML110 G7 Specifications

General

Product Type	Server
Form Factor	Tower
Processor Sockets	1
Chipset	Intel C202
Memory Type	DDR3 UDIMM
Maximum Memory	16 GB
Memory Slots	4
Processor	Intel Xeon E3-1200 series
Storage	SAS or SATA
Drive Bays	4 LFF or 8 SFF
Hard Drives	Optional
Optical Drive	Optional
Network Controller	HP NC112i Gigabit Ethernet Adapter (1 port)
Operating System Support	Microsoft Windows Server, Red Hat Enterprise Linux, SUSE Linux Enterprise Server
Storage Controller	HP Dynamic Smart Array B120i

Summary

Component Identification

Front Panel Components

Identifies and describes components on the server's front panel.

Front Panel LEDs and Buttons

Details the status indicators and controls on the server's front panel.

Rear Panel Components

Identifies and describes components on the server's rear panel.

Rear Panel LEDs and Buttons

Details the status indicators and controls on the server's rear panel.

System Board Components

Lists and describes components located on the server's system board.

DIMM Slot Locations and Maintenance Switch

Shows DIMM slot locations and explains the system maintenance switch.

System Board LEDs and NMI Functionality

Describes system board LEDs and the NMI feature for crash dumps.

Drive LEDs and Combinations

Explains SAS/SATA drive LEDs and their status interpretations.

Cache Module LEDs

Describes LEDs for BBWC and FBWC cache modules.

Fan Locations

Identifies the locations of system fans within the server chassis.

Server Operations

Powering Up and Down the Server

Procedures for safely powering the server on and off.

Accessing the Server Chassis

Steps to unlock, open, remove, and install the server's tower bezel and access panel.

Air Baffle Installation and Removal

Procedures for removing and installing the internal air baffle for proper cooling.

Server Setup and Installation

Installation Services and Environment

Details optional HP services and environmental setup requirements for the server.

Server Power and Grounding

Covers electrical power requirements, safety, and proper grounding procedures.

Initial Server Configuration

Steps for setting up a tower or rack server, including power-up and initial configuration.

Operating System and Registration

Guidance on installing the operating system and registering the server with HP.

Hardware Options Installation

Drive Installation

Covers drive options, installation guidelines, and installing individual drives and drive cages.

Other Hardware Options

Details installation of drive LED cables, storage controllers, BBWC/FBWC, optical drives, and memory.

Expansion Boards and iLO

Procedures for installing expansion boards and the dedicated iLO management port.

Trusted Platform Module and RPS

Installation and enablement of the Trusted Platform Module and RPS Enablement Kit.

Cabling Procedures

Storage Drive Cabling

Details cabling for various SAS/SATA drive configurations, including hot-plug and non-hot-plug.

Optical and Battery Cabling

Instructions for connecting optical drives and battery/capacitor packs.

Power Supply Cabling

Covers cabling for non-redundant and redundant power supply configurations.

Configuration and Utilities

Configuration Tools

Overview of SmartStart, Scripting Toolkit, RBSU, ACU, and ORCA utilities.

Management and Diagnostic Tools

Details ASR, ROMPaq, iLO, Erase Utility, USB support, and HP Insight Diagnostics.

System Updates and Support

Information on keeping the system current with drivers, firmware, PSPs, and HP support services.

Troubleshooting Guide

Troubleshooting Resources and Steps

Guides to troubleshooting resources, pre-diagnostic steps, and safety information.

Symptom Gathering and Preparation

How to collect symptom information and prepare the server for diagnosis.

Troubleshooting Flowcharts

A collection of diagnostic flowcharts for various problem categories.

Specific Problem Flowcharts

Flowcharts for power-on, POST, OS boot, and server fault indication issues.

Battery Replacement

Procedure for replacing the server's internal battery.

Safety, Regulatory, and Specifications

Regulatory Compliance and ESD

Covers safety, regulatory compliance, and preventing electrostatic discharge.

Product Specifications

Details environmental, mechanical, and power supply specifications for the server.

Support and Documentation

Preparing for Support and CSR

Information needed before contacting HP and details on Customer Self Repair.

Acronyms, Abbreviations, and Feedback

Glossary of terms used in the manual and how to provide feedback.

Related product manuals

HP ProLiant ML110 Gen9

138 pages

HP HPE ProLiant ML110 Gen9

135 pages

HP ProLiant ML110 - G2 Server

120 pages

HP ProLiant ML110 Generation 5

98 pages

HP ProLiant ML110 Generation 3

56 pages

ProLiant ML110 Generation 5 (G5)

30 pages

ProLiant ML110 Generation 6 (G6)