How to fix HS Medical Equipment chair that won't turn on?
If your HS Medical Equipment chair isn't operating, and you don't hear a beep when power is applied, even though the outlet has power: * Check all wiring connections to ensure they are properly plugged in. * Verify that there is AC power at the wall receptacle. If not, restore outlet power. * Inspect the line fuse and replace it if it's blown.
Why won't the base of my HS 6200 chair raise?
If the base of your HS Medical Equipment chair isn't raising, it could be due to a few reasons: 1. There might be no power going to the pump motor. Check for voltage to the pump motor assembly. 2. The up-limit switch may be stuck in the "open" position. Try to readjust or replace the switch. 3. The pump motor might be burned out, requiring you to replace the pump motor assembly.
What to do if footswitch on HS Medical Equipment is not working?
If the footswitch functions on your HS Medical Equipment are not operating, the footswitch cord might not be connected properly. Check all internal and external footswitch wiring.
How to troubleshoot a HS Medical Equipment chair base that won't lower?
If your HS Medical Equipment chair base won't lower from the floor unit: * The solenoid valve might not be closed due to dirt in the valve. Consider repairing or replacing the solenoid valve. * There might be constant power applied to the solenoid. Check for switches that are stuck in the "closed" position.
Why are the backswitch functions not working on my HS Medical Equipment chair?
If the backswitch functions are not operating on your HS Medical Equipment chair, there may be damaged or disconnected wires in the chair back, under the chair seat, or in the chair base. Check all wiring connections.
General| Brand | HS |
|---|---|
| Model | 6200 |
| Category | Medical Equipment |
| Language | English |
Explains the meaning of DANGER, WARNING, CAUTION, and NOTE symbols.
Details the required environmental conditions for safe transportation and storage of the equipment.
Explains the meaning of DANGER, WARNING, CAUTION, and NOTE symbols used throughout the manual.
Provides contact information for support and questions regarding Reliance products.
Details the chair's classification regarding electric shock, fire, and mechanical hazards.
Warns against exposing the equipment to rain or moisture to prevent hazards.
Alerts about the explosion hazard if used with flammable anesthetics.
Lists electrical and safety ratings for the 120V model chair.
Lists electrical and safety ratings for the 230V model chair.
Discusses potential interference and user remedies for radio frequency energy.
Warns about the effect of low storage temperatures on hydraulic oil.
Provides step-by-step instructions for unpacking the chair and its components.
Details the procedure for assembling the chair and its parts.
Instructions for attaching the headrest to the chair back.
Guidance on connecting power cords and cables to the chair.
Notes on connecting the chair's control cable to a Reliance instrument stand.
How to raise and lower the chair using the membrane switches on the chair back.
How to raise and lower the chair using the footswitch controls.
Instructions on reclining and raising the chair back using the release lever.
Details on how to rotate the chair upper structure and its locking mechanism.
Instructions for raising, lowering, and locking the chair arms for patient access.
Caution regarding using the chair in the specified position for stability.
Warning about exceeding the maximum patient weight limit and static loads.
Instructions on how to retract the footrest near its outer edge.
How to operate and adjust the standard No. 18 headrest for position and tension.
How to operate the No. 10 headrest by adjusting its sliding pillow section.
How to operate and adjust the No. 11 and 21 headrests using their handles.
Step-by-step guide to replacing fuses in the AC input module.
Critical warnings regarding fuse replacement, including correct type and handling.
Recommendations for cleaning upholstery, including stain removal and disinfection.
How to clean the chair's durable, powder-coated painted metal surfaces.
Lists tested and recommended disinfectants for the chair's upholstery and surfaces.
Safety precautions and warnings when using cleaning solvents and disinfectants.
Advice on how to order replacement parts, including necessary model and serial numbers.
Lists parts for the chair top assembly with corresponding item numbers.
Lists parts for the base assembly with corresponding item numbers.
Lists parts for various headrest assemblies with corresponding item numbers.
Details of the electrical schematic, including components, connections, and wire color codes.
Outlines the conditions, limitations, and claim process for the product warranty.
To Next Page