Hubbell Versa-Tech I User Manual (English)

Other manuals for Hubbell Versa-Tech I

Installation, Operation And Maintenance Manual50 pages

Questions and Answers:

A
Arthur CarterAug 13, 2025
What to do if Hubbell Power Tool programming software does not communicate with recloser?
- N
  Natalie GrayAug 13, 2025
  If the Hubbell Power Tool programming software isn't communicating with the recloser, there might be a few reasons: * The cable could be faulty: Check Section 6 for the correct cable specifications. * There might be a poor cable connection: Make sure the cable is securely connected at both ends. * The communication port might be unselected or incorrectly selected: Ensure that the correct port is selected and that it matches the connected cable.
B
brownjonathanAug 16, 2025
Why Hubbell Power Tool recloser does not close?
- A
  annaharveyAug 16, 2025
  If the Hubbell Power Tool recloser isn't closing, it could be due to these reasons: * The handle might not be fully closed: Ensure the handle is completely closed (up). * The batteries might be low: Replace the batteries.
A
abaileyAug 20, 2025
What to do if Hubbell Power Tool recloser does not automatically reclose?
- E
  Erin Curry MDAug 20, 2025
  If the Hubbell Power Tool recloser doesn't automatically reclose, the non-reclosing lever might be down. To fix this, move the non-reclosing lever to the up position.
P
Paul CooperAug 25, 2025
What to do if Hubbell Power Tool recloser does not open?
- T
  Tammy SmithAug 25, 2025
  If the Hubbell Power Tool recloser does not open, it might be due to a damaged mechanism. In this case, you should consult a factory representative.
D
Donna AndersonAug 28, 2025
Why does Hubbell Versa-Tech I programming software not communicate with the recloser?
- L
  Luke GrayAug 28, 2025
  Several factors can cause communication issues between the programming software and the recloser: * A faulty cable may be the root cause. * A poor cable connection at either end can disrupt communication. Ensure the cable is securely connected at both ends. * The communication port might be unselected or incorrectly selected. Verify that the correct port is selected and that the connected cable matches the selected port.
J
Joseph CisnerosSep 1, 2025
What to do if Hubbell Versa-Tech I Industrial Equipment recloser does not close?
- C
  Christian VangSep 1, 2025
  If the recloser isn't closing, check the following: 1. Ensure the handle is fully closed (pushed all the way up). If not, adjust it to the fully closed position. 2. The battery might be low. If so, replace it with a new one. 3. If the device is in HLT mode (only for v4.xx firmware), further actions may be required.
K
Kathy PriceSep 5, 2025
Why does Hubbell Versa-Tech I recloser not automatically reclose?
- S
  Sean PruittSep 5, 2025
  If the recloser isn't automatically reclosing, the non-reclosing lever might be down. Move the non-reclosing lever to the up position to enable automatic reclosing.
M
Matthew SandersSep 8, 2025
What to do if Hubbell Versa-Tech I recloser does not open?
- L
  Laura ArcherSep 8, 2025
  If the recloser is not opening, it may be due to a damaged mechanism. Consult a factory representative for assistance.

Hubbell Versa-Tech I Specifications

General

Category	Industrial Equipment
Brand	Hubbell
Voltage Rating	600 VAC
Poles	3
IP Rating	IP67
Housing Material	Thermoplastic
Operating Temperature	-40°C to 60°C
Agency Approvals	UL

Related product manuals

Hubbell VERSA-TECH LT

50 pages

Hubbell GAI-TRONICS 234

12 pages

Hubbell Versa-Tech I User Manual

Table of Contents

Other manuals for Hubbell Versa-Tech I

Questions and Answers:

Hubbell Versa-Tech I Specifications

Related product manuals