Hunter 99110 - User Manual

www.HunterFan.com
1.888.830.1326
Model #99110
Universal Ceiling
Fan Remote Control
Installation
Wiring
OR OR OR
OFF
Remove the canopy. If uncertain
how to remove it, reference the fan’s
owner’s manual. With wiring exposed,
it may be helpful to note existing wire
connections or take a digital photo for
reference. Remove the wire connectors
that connect the wires from the outlet
box to the fan, leaving the grounding
wires connected.
CONNECT WIRES FROM RECEIVER TO FAN -Using the blue wire connectors connect the white wire from the
receiver (marked “common out”) to the white wire from fan. Connect the black wire from the receiver (marked
“fan out”) to the black wire from the fan. Connect the blue wire from the receiver (marked ”light out”) to the
blue wire (or possibly black with white stripe) from the fan.
Note: The red wire from the receiver has a pre-installed wire terminator. It will not be used.
If you’re uncertain about wire colors or connections, please contact a qualied electrician.
CONNECT WIRES FROM RECEIVER TO WIRES FROM OUTLET BOX - Using an orange wire connector connect
the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked “live in”). Connect
the white wire (grounded) from the ceiling to the white wire from the receiver (marked “neutral in”).
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.
Before installing the
Universal Remote Control,
use the pull chains to set
the fan speed to HIGH
and the light to ON.
Be sure power is OFF
before proceeding with
installation.
Choose the hanging system that most closely resembles the one used by your fan and install the receiver and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess
wire into the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling.
Ceiling
Plate
Receive
r
Canopy
Receiver
Canopy
Ceiling
Bracket
Receiver
Fan Body
Cable Tie
For low prole fans, the receiver should
be secured to the hanger bracket with
a cable tie.
Receiver
Canopy
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
To avoid possible electrical shock, before installing or servicing your fan, disconnect the
power by turning off the circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off position, securely fasten a
prominent warning device, such as a tag, to the service panel.
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded)
white (grounded) white (neutral in)
black (live in)
F
R
O
M
R
E
C
E
I
V
E
R
white
black
blue
white (common out)
black (fan out)
blue (light out)
F
R
O
M
F
A
N
M0032-01 • 09/05/12 • © Hunter Fan Company

Summary

Installation Guide

Preparation and Safety

Ensure power is OFF before installation. Set fan speed to HIGH and light to ON using pull chains.

Canopy Removal

Remove the fan canopy. Note existing wire connections or take a photo for reference.

Hanging System and Receiver Installation

Choose the correct hanging system. Install the receiver, securing it with a cable tie for low profile fans.

Wiring Connections

Connect receiver wires to fan wires (common, fan out, light out) and outlet box wires (live in, neutral in).

Device Operations and Maintenance

Battery Replacement

Access battery compartment by removing the Phillips head screw. Replace with CR2032 battery, positive side up.

Remote Pairing Process

Pair remote by pressing Fan Off and High buttons for 4 seconds within 3 minutes of restoring power.

Fan Speed and Light Control

Use speed buttons (High, Medium, Low) to turn the fan on. Press Light to toggle or hold to adjust brightness.

Safe-Exit Feature

Initiate by holding the fan power button off for 3 seconds. Lights flash, then dim over 30 seconds.

Troubleshooting Common Issues

Addresses fan not starting, erratic control, limited range, and lights not dimming, including CFL compatibility.

Hunter 99110 Specifications

General

Type	Ceiling Fan Remote Control
Compatibility	Hunter ceiling fans
Power Source	Battery
Color	White
Number of Speeds	3
Battery Type	AAA
Batteries Required	Yes