Hunter 99122 - User Manual

www.HunterFan.com
1.888.830.1326
Model 99122, 99123
Universal 3 Speed
Ceiling Fan Remote
Installation
OR OR OR
Remove the canopy. If uncertain
how to remove it, reference the fan’s
owner’s manual. With wiring exposed,
it may be helpful to note existing wire
connections or take a digital photo for
reference. Remove the wire connectors
that connect the wires from the outlet
box to the fan, leaving the grounding
wires connected.
Before installing the
Universal Remote Control
Receiver, use the pull chains
to set the fan speed to HIGH
and the light to ON. Be
sure power is OFF before
proceeding with installation.
Choose the hanging system that most closely resembles the one used by your fan and install the receiver as shown and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess
wire into the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.
Ceiling
Plate
Receive
r
Canopy
Receiver
Canopy
Ceiling
Bracket
Receiver
Fan Body
Cable Tie
For low prole fans, the receiver should
be secured to the ceiling bracket with a
cable tie.
Receiver
Canopy
M0060-01 • 01/15/14 • © Hunter Fan Company
Turn Power
OFF
If you are installing multiple remote-controlled fans
on the same circuit breaker,
you may need to perform a few extra steps to prevent
interference or faulty operation of your remote controls.
Go to www.HunterFan.com/FAQs and click “How do I properly
install multiple remote-controlled fans?” for more information.
Wiring
CONNECT WIRES FROM RECEIVER TO FAN - Using the orange wire connectors, connect the blue wire from the
receiver to the blue wire (or possibly black with white stripe wire) from the fan. Connect the yellow wire from the
receiver to the black wire from the fan.
If you’re uncertain about wire colors or connections, please contact a qualied electrician.
CONNECT WIRES FROM RECEIVER AND FAN TO WIRES FROM OUTLET BOX - Using the orange wire connectors,
connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire
(grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
To avoid possible electrical shock, before installing or servicing your fan, disconnect
the power by turning off the circuit breakers to the outlet box and associated wall
switch location. If you cannot lock the circuit breakers in the off position, securely
fasten a prominent warning device, such as a tag, to the service panel.
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
R
E
C
E
I
V
E
R
black
blue
yellow
blue
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
black
white white (grounded)
black (ungrounded)
white
F
R
O
M
F
A
N

Summary

Ceiling Fan Installation Guide

Preparation and Power Off

Turn fan speed to HIGH, light ON. Ensure power is OFF before proceeding with installation.

Canopy and Wire Management

Remove canopy, note existing connections, and prepare wires for receiver installation.

Receiver Placement and Grounding

Install receiver per hanging system, ensuring fan and bracket remain grounded.

Ceiling Fan Wiring Connections

Connect Receiver to Fan Wires

Connect receiver blue wire to fan blue wire, and receiver yellow to fan black wire.

Connect Receiver;Fan to Outlet Box

Connect ceiling black to receiver black, and ceiling white to receiver/fan white.

Final Wiring & Canopy Re-installation

Secure all wire connectors, push wires into outlet box, and re-install the canopy.

Remote Control Operation and Setup

Pairing the Remote to the Fan

Press Fan Off and High buttons within 3 mins of restoring power to sync remote and fan.

Fan Speed and Light Control

Use Fan Off, speed buttons to control fan; press Light button to toggle or hold to dim.

Safe-Exit Lighting Feature

Press Fan Off for 3s to activate Safe-Exit; lights dim over 30s for safe exit.

Remote Control Maintenance and Troubleshooting

Battery Replacement

Replace CR2032 battery with positive side up, securing the battery door.

Transmitter Cradle Installation

Mount cradle to switch cover plate using screws, breaking off tabs for paddle switches.

Common Troubleshooting Issues

Addresses fan not starting, erratic control, dimming issues, and CFL bulb compatibility.

Hunter 99122 Specifications

General

Type	Ceiling Fan Remote Control
Compatibility	Hunter Ceiling Fans
Brand	Hunter
Model	99122
Functions	Fan speed control, light dimming
Battery Type	AAA